Filter
Top Products
page 6
TOOL ASSEMBLY
Removing and Replacing Quik-Lok
®
Cords (Select Models) (Fig. 1)
MILWAUKEE's exclusive Quik-Lok
®
Cords provide instant field replace-
ment or substitution.
1. To remove the Quik-Lok
®
Cord, turn the cord nut 1/4 turn to the left
and pull it out.
2. To replace the Quik-Lok
®
Cord, align the connector keyways and
push the connector in as far as it will go. Turn the cord nut 1/4 turn
to the right to lock.
Installing the Side Handle
The side handle may be installed on either side of gear case for right or
left handed use. Position side handle in the location which offers best
control and guard protection. For operating zones that provide maximum
protection for the operator, see "Grinding". To install, thread side handle
into side handle socket on desired side of gear case and tighten securely.
Fig. 1
Installing, Adjusting, and Removing the Guard (Select Models)
The guard must be used when using the tool as a grinder. The guard
should be removed when using tool as a sander.
1. Unplug the tool and place it upside down on a level surface. Remove
any accessories from the spindle.
2. Place the grinding wheel guard over the spindle. Position the guard
in the location which offers best control and guard protection. For
operating zones that provide maximum protection for the operator,
see "Grinding".
3. Fasten the guard to the lower half of the gear case with screws and
lock washers provided.
Starting and Stopping the Motor
1. To start the tool, pull the trigger.
2. To stop the tool, release the trigger.
Locking the Trigger (Select Models)
The lock button holds the trigger in the ON position for continuous use.
1. To lock the trigger on, hold in the lock-on button while pulling the
trigger. Release the trigger.
2. To unlock the trigger, pull the trigger and release. The lock-on but-
ton will pop out.
Using the Dial Speed Control (Cat. No. 6078 only)
Cat. No. 6078 has a dial speed control and variable speed trigger switch.
The maximum speed may be preset using the speed control dial and the
speed may be varied by the trigger switch. Speed control dial settings
range from 1 to 5. Lower numbers correspond to lower speeds and
higher numbers correspond to higher speeds. Use the setting that best
suits the work.
To control the speed, set the dial to the desired number. Then, pull the
trigger. Increase or decrease pressure on the trigger to vary the speed.
To stop the tool, release the trigger.
OPERATION
WARNING!
To reduce the risk of injury, wear safety goggles or glasses
with side shields. Unplug the tool before changing
accessories or making adjustments.
Use sanding discs and grinding wheels that are:
• correct size as written on tool's nameplate
• correct wheel type and grit for the job
• rated at or above the RPM listed in the “WARNING” section on
the tool's nameplate
Use backing pads, adapters, and other accessories that are:
• correct size for tool and for sanding disc or grinding wheel
• rated at or above the RPM listed in the “WARNING” section on
the tool's nameplate
• the proper accessory for the job
Sanding Disc and Grinding Wheel Material
Sanding discs and grinding wheels are made of various materials and
are designed for different jobs. Be sure that you choose the proper
sanding disc or grinding wheel for the job you plan to do.
WARNING!
To reduce the risk of injury or damage to the tool, do not use
the spindle lock button to stop the spindle while the tool is
in use or is coasting after shut-off.
WARNING!
To reduce the risk of personal injury and damage to the tool,
use ONLY accessories rated at or above the RPM listed on
the “WARNING” section of the tool's nameplate.
Sanding Disc and Grinding Wheel Selection
WARNING!
To reduce the risk of injury, always unplug tool before
attaching or removing accessories or making adjustments.
Use only specifically recommended accessories. Others
may be hazardous.
To reduce the risk of injury when grinding, ALWAYS use the
proper guard. ALWAYS properly install the guard.
WARNING!