Filter
Top Products
To Attach Drive Pad Holder
or Brush:
Lay the floor machine on its back
with the handle lying on the floor.
This exposes the brush holder
pan. Place the brush or drive pad
holder over the round brush
holder pan making sure it is in
place.
CAUTION: NEVER put the brush or pad holder on the machine
by placing it on the floor and moving the running machine over
it, or by placing the machine over the brush or pad holder and
then starting the motor.
To Remove Brush:
Lay machine on its back and pull brush or pad holder off the
round holder pan.
To Use Machine:
The Orbiter's on-off switch is
located on the handle. It has
been designed to be conve-
niently activated. On (I) - Off(O)
is printed on the switch. BE
CAREFUL that the switch is in the
OFF (O) position before you
plug the electric cord into the
outlet. Before turning the
machine on, be sure there is a
pad or brush in place on the machine.
To Guide the Floor Machine:
Grasp the unique “T” handle and glide the machine across the
floor in a back and forth motion. The patented “T” handle feature
gives you complete control. The Orbiter's perfectly balanced
counter-weight system gives smooth and easy action with
fingertip control.
IMPORTANT
- Always wear shoes when using your
Orbiter. Before completing any of the following
pr
ocedur
es for the first time, test a small hidden ar
ea.
Care of your Oreck Floor Machine:
This is a precision machine. Dropping, unreasonable bumping
or r
ough handling may r
esult in damage to the balanced
counter-weight system.
Wrap your cord loosely around the two
hooks on the handle.
Remove brushes after use. The bristles
may be damaged due to the weight of the machine. Stor
e your
machine in the upright position. After each use, remove wax or
cleaning solutions. After sanding, blow sawdust off motor.
Clean housing and bumper with damp cloth after each use. A
little car
e will keep your Orbiter looking like new
.
USER MAINTENANCE:
Lubrication: The Orbiter motor bearings ar
e factory lubricated
and sealed. All other ser
vicing should be per
for
med by an
authorized service center. There are no user serviceable parts
inside.
ON/OFF
SWITCH
Operating Instructions
Warranty
ORECK MANUF
ACTURING COMPANY: (Oreck 21180
Johnson Road; Long Beach, MS, USA 39560 gives you the
following warranty for this product only if it was originally
purchased for use, not resale from Oreck or an Oreck
Authorized Retail Dealer.)
Oreck will repair or replace, free of charge, to the original
purchaser, any part that is found to be defective in material
or workmanship within one (1) year of the date of purchase.
ORB555MC models carry a (5) five year limited motor
warranty which applies to residential use. Note: If the unit
is used commercially, a (1) one year overall warranty
applies.
Brushes, pads, drive blocks and other parts are subject to
normal wear and are not covered by this warranty.
This warranty does not apply to any part subjected to
accident, abuse, alteration, misuse, damage caused by act
of God, the use of voltages other than indicated on the serial
number displayed on this product or service of this product
by other than Oreck or a participating Factory Authorized
Service Center.
Oreck does not authorize any person or representative to
assume or grant any other warranty obligation with the sale
of this product.
Oreck’s warranty is valid only if you retain proof of
purchase from Oreck or an Oreck Authorized Retail Dealer
for this product. If you purchase this product from any other
source, your purchase is “AS IS,” which means Oreck grants
you no warranty, and that you, not Oreck, assume the entire
risk of the quality and performance of this product, including
the entire cost of any necessary servicing or repairs of any
defects.
This warranty is in addition to your statutory and other legal
rights.
The Orbiter
®
is the most advanced, easiest to use machine of its
kind. With proper care and use, your Orbiter will last a lifetime.
This booklet will tell you how to care for the Orbiter and all
about its featur
es, accessories and their use.
Your Orbiter floor machine comes completely assembled and
ready to operate once the Drive Pad Holder or Brush is attached.
The of
f/on switch has inter
national symbols (O) OFF and ( l ) ON.
CAUTION: NEVER WORK ON THE MACHINE WHILE IT IS
PLUGGED IN - ALWAYS DISCONNECT it from the electrical outlet.
When leaving machine unattended, be sure to disconnect it.
To Replace the Fuse:
When changing fuse, replace
with the same size fuse.
3
ENGLISH