Filter
Top Products
4 5
1. DANGER!:
Keep hands away from cutting area
and blade. Keep your second hand
on auxiliary handle or motor housing.
If both hands are holding the saw, they
cannot be cut by the blade.
Do not reach underneath the work-
piece. The guard cannot protect you
from the blade below the workpiece.
Adjust the cutting depth to the thick-
ness of the workpiece. Less than a full
tooth of the blade teeth should be visible
below the workpiece.
NEVER hold piece being cut in your
hands or across your leg. Secure the
workpiece to a stable platform. It is
important to support the work properly to
minimize body exposure, blade binding,
or loss of control.
Hold power tool by insulated grip-
ping surfaces when performing an
operation where the cutting tool may
contact hidden wiring or its own cord.
Contact with a “live” wire will also make
exposed metal parts of the tool “live” and
shock the operator.
When ripping always use a rip fence
or straight edge guide. This improves
the accuracy of cut and reduces the
chance of blade binding.
Always use blades with correct size
and shape (diamond versus round) of
arbor holes. Blades that do not match
the mounting hardware of the saw will
run eccentrically, causing loss of con-
trol.
Never use damaged or incorrect blade
washers or bolts. The blade washers
and bolts were specially designed for
your saw, for optimum performance and
safety of operation.
2. Causes and Operator Prevention of
KICKBACK:
KICKBACK is a sudden reaction to
a pinched, bound or misaligned saw
blade, causing an uncontrolled saw to
lift up and out of the workpiece toward
the operator.
SPECIFIC SAFETY RULES — CIRCULAR SAWS
When the blade is pinched or bound
tightly by the kerf closing down, the
blade stalls and the motor reaction
drives the unit rapidly back toward the
operator.
If the blade becomes twisted or mis-
aligned in the cut, the teeth at the back
edge of the blade can dig into the top
surface of the wood causing the blade
to climb out of the kerf and jump back
toward operator.
KICKBACK is the result of saw misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below:
Maintain a fi rm grip with both hands
on the saw and position your arms to
resist kickback forces. Position your
body to either side of the blade, but not
in line with the blade. Kickback could
cause the saw to jumb backwards, but
kickback forces can be controlled by
the operator, if proper precautions are
taken.
When blade is binding, or when inter-
rupting a cut for any reason, release
the trigger and hold the saw motion-
less in the material until the blade
comes to a complete stop. Never
attempt to remove the saw from the
work or pull the saw backward while
the blade is in motion or kickback
may occur. Investigate and take cor-
rective actions to eliminate the cause
of blade binding.
When restarting a saw in the work-
piece, center the saw blade in the kerf
and check that saw teeth are not en-
gaged into the material. If saw blade is
binding, it may walk up or kickback from
the workpiece as the saw is restarted.
Support large panels to minimize the
risk of blade pinching and kickback.
Large panels tend to sag under their
own weight. Supports must be placed
under the panel on both sides, near
the line of cut and near the edge of the
panel.
Do not use dull or damaged blade.
Unsharpened or improperly set blades
produce narrow kerf causing excessive
friction, blade binding and kickback.
Blade depth and bevel adjusting lock-
ing levers must be tight and secure
before making cut. If blade adjustment
shifts while cutting, it may cause binding
and kickback.
Use extra caution when making a
"plunge cut" (or pocket cut) into
existing walls or other blind areas.
The protruding blade may cut objects
that can cause kickback.
3. Check lower guard for proper closing
before each use. Do not operate saw
if lower guard does not move freely
and close instantly. Never clamp or
tie the lower guard into the open po-
sition. If saw is accidentally dropped,
lower guard may be bent. Raise the
lower guard with the lower guard lever
and make sure it moves freely and does
not touch the blade or any other part, in
all angles and depths of cut.
Check the operation of the lower
guard spring. If the guard and the
spring are not operating properly,
they must be serviced before use.
Lower guard may operate sluggishly due
to damaged parts, gummy deposits, or
a buildup of debris.
Lower guard should be retracted
manually only for special cuts such
as "plunge cuts" ("pocket cuts") and
"compound cuts". Raise lower guard
by lower guard lever and as soon as
blade enters the material, the lower
guard must be released. For all other
sawing, the lower guard should operate
automatically.
Depth of Cut
at 45°
0 to 1-9/16"
Blade
Size
6-1/2"
Cat.
No.
0730-20
Depth of Cut
At 90°
0 to 2-1/8"
Arbor
5/8"
No Load
RPM
4200
Volts
DC
28
Specifi cations
Symbology
Volts Direct Current
No Load Revolutions
per Minute (RPM)
Underwriters Laboratories, Inc.,
United States and Canada
Always observe that the lower guard
is covering the blade before plac-
ing saw down on bench or fl oor. An
unprotected, coasting blade will cause
the saw to walk backwards, cutting
whatever is in its path. Be aware of the
time it takes for the blade to stop after
switch is released.
4. Maintain labels and nameplates.
These carry important information.
If unreadable or missing, contact a
MILWAUKEE service facility for a free
replacement.
5. WARNING! Some dust created by
power sanding, sawing, grinding, drill-
ing, and other construction activities
contains chemicals known to cause
cancer, birth defects or other reproduc-
tive harm. Some examples of these
chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and
cement and other masonry products,
and
• arsenic and chromium from chemi-
cally-treated lumber.
Your risk from these exposures varies,
depending on how often you do this
type of work. To reduce your exposure
to these chemicals: work in a well ven-
tilated area, and work with approved
safety equipment, such as those dust
masks that are specially designed to
fi lter out microscopic particles.