Filter
Top Products
22 23
Fig. 29
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Electric tools used on fiberglass material, wall board, spack ling
compounds, or plaster are subject to ac cel er at ed wear and
possible premature failure be cause the fi ber glass chips and
grindings are highly abrasive to bearings, brushes, com mu -
ta tors, etc. Consequently, we do not recommended us ing this
tool for extended work on these types of materials. How ev er,
if you do work with any of these materials, it is extremely
important to clean the tool using com pressed air.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
ADJUSTMENTS
To adjust the lasers in a rotational direction:
n Remove the blade.
n Plug in the saw.
n Rest the back of the base on scrap workpiece.
n Insert a flathead screwdriver into the laser barrel slot.
n Turn laser on.
NOTE: DO NOT look directly into the laser beam.
n Turn the barrel left or right as necessary.
n Since blade thicknesses vary, always make a trial cut in
scrap workpiece to ensure an accurate cut.
n Check for proper alignment.
n Repeat as necessary until laser is aligned.
WARNING:
Use of controls or adjustments or performance of pro-
cedures other than those specified herein could result in
hazardous radiation exposure.
RYLD
Complieswith21CFRparts1040.10and1040.11
RYLD
Compleconlanorma21CFRpartes1040.10y1040.11
RYLD
Conformeauxparties1040,10et1040,11de21CFR
WARNING:
When servicing, use only iden ti cal replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
MAINTENANCE
Potencia máx. <5mW
Long. de onda: 650 nm
Aparato láser Clase IIIa
Radiación láser, evite el
contacto ocular directo.
Rayonnement laser –
éviter l’exposition
Puissance max. <5 mW
Longueur d’onde : 650 nm
Produit laser de classe IIIa
RYLD
PELIGRO
Complieswith21CFRparts1040.10
and1040.11
RYLD
Compleconlanorma21CFRpartes
1040.10y1040.11
RYLD
Conformeauxparties1040,10et
1040,11de21CFR
Rayonnement
laser
lorsqu’ouvert,
ÉVITER
L’EXPOSITION
Cetteouverture
produit un
rayonnement
laser.
éviterlecontact
oculairedirect.
PELIGRO
EVITE
EXPONERSE
abierto,evitela
exposición
directade
losojos.
Radiaciónláser
cuandoestá
Estaabertura
emiteradiación
láser.
PELIGRO
EVITE
EXPONERSE
abierto,evitela
exposición
directade
losojos.
Radiaciónláser
cuandoestá
Estaabertura
emiteradiación
láser.
Rayonnement
laser
lorsqu’ouvert,
ÉVITER
L’EXPOSITION
Cetteouverture
produit un
rayonnement
laser.
éviterlecontact
oculairedirect.