Filter
Top Products
-8-
D('*0()$Jg\\[;i`ccGi\jj
J8=<KP
8[[`k`feXcJX]\kp@ejkilZk`fej]fi;i`ccGi\jj\j
LJ<k_`jXe[fk_\idXZ_`e\ipn`k_ZXlk`fe
Xe[ i\jg\Zk% 8cnXpj Zfej`[\i jX]\kp ]`ijk#
Xj `k Xggc`\j kf pfli `e[`m`[lXc nfib`e^
Zfe[`k`fej%Efc`jkf]jX]\kp^l`[\c`e\jZXe
Y\ Zfdgc\k\Ç\m\ip j_fg \em`ifed\ek `j
[`]]\i\ek%=X`cli\kf]fccfn^l`[\c`e\jZflc[
i\jlck `e j\i`flj g\ijfeXc `ealip# [XdX^\
kf\hl`gd\ekfigffinfibi\jlckj%
I<8;Xe[le[\ijkXe[k_`j
\ek`i\ `ejkilZk`fe dXelXc
Y\]fi\lj`e^k_`jdXZ_`e\%
J\i`flj g\ijfeXc `ealip
dXp fZZli `] jX]\kp Xe[
fg\iXk`feXc`e]fidXk`fe`j
efk le[\ijkff[ Xe[ ]fc$
cfn\[% ;F EFK i`jb pfli
jX]\kpYpefki\X[`e^
(% <P<&=8:<&?8E;GIFK<:K@FE% A face shield used with safety glasses is recommended. Always
keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! DO
NOT wear gloves when operating the drill.
)% J<:LI@E>9@K% Properly tighten and securely lock the drill bit in the chuck.
*% :FII<:K9@K% Use only round, hex, or triangular shank drill bits, or tapered shank drill bits mated
with the appropriate sleeve.
+% 8;ALJK@E>B<PJ8E;NI<E:?<J% Remove all adjusting keys and wrenches before turning the
machine FE.
,% ;I@CC@E>J?<<KD<K8C% Never drill sheet metal unless it is securely clamped to the table.
-% JLI=8:<&NFIBG@<:<GI<G8I8K@FE% Never turn the drill press FE before clearing the table
of all objects (tools, scrap wood, etc.) DO NOT drill material that does not have a flat surface,
unless a suitable support is used.
.% ;8D8><;KFFCJ% Never use tools in poor condition. Dull or damaged cutting tools are hard to
control and may cause serious injury.
/% ;I@CCFG<I8K@FE% Never start the drill press with the drill bit pressed against the workpiece.
Feed the drill bit evenly into the workpiece. Back the bit out of deep holes. Turn the machine
F== and clear chips and scrap pieces with a brush. Shut power F==, remove drill bit, and clean
table before leaving the machine.
0% FG<I8K@E>JG<<;% Always operate your drill press at speeds that are appropriate for the drill bit
size and the material that you are drilling.
('% D8@EK<E8E:<&JG<<;:?8E><J% Never do maintenance or change speeds with the machine
plugged in.
((%DFLEK@E>NFIBG@<:<J% Use clamps or vises to secure workpiece before drilling. Position work
so you avoid drilling into the table.
()%K89C<CF:B% Make sure the table lock is tightened before starting the drill press.