Filter
Top Products
5. REGULAR OPERATING MODE
5. REGULAR OPERATING MODE (CONT)
The Wall Dimmer can control the light in 2 different operating modes:
1) On / Off Mode - Allows operating the light either on or off, without
dimming function.
2) Dimming Mode - Allows operating the light in on, off or dimming
(dim / brighten). Light source must be either incandescent light
or dimmable compact fluorescent light.
The factory default operating mode is On/Off mode. However, if your
light is dimmable, you may change the operating mode to Dimming
Mode. To change the operating modes, please follow the instructions
below:
1. Turn on the light by the programmed transmitter or touch pad.
2. Press and hold the button on the transmitter that is programmed to
the Wall Dimmer for 10 seconds
.
3. The light will flash. If it flashes once, that means it is in On / Off Mode.
If it flashes twice, that means it is in Dimming Mode.
4. Repeating step 2 above will toggle the setting between On / Off Mode
and Dimming Mode.
or touch the touch pad for 10 seconds
with your finger.
5.1 ON / OFF operation:
Use a Transmitter
Wall Dimmer allows on / off operation, when the programmed button is
pressed, it will transmit a signal to toggle the status of the load.
For example, if a toggle signal is received when the light is off, that signal
will turn on the light.
5.2 Brightness control operation:
6. FLASHING ALERT OPERATING MODE
Besides turning on and off the light, you may also control the brightness
of the light if the light bulb is either incandescent light or dimmable compact
fluorescent light.
Use the Wall Switch
Turn on the light first. Then keep touching the touch pad to change the
brightness. Remove your finger from the touch pad until the desired
brightness is reached. To change the the opposite way,
remove your finger from the touch pad and then keep touching
Use a Transmitter
First turn on the light.
Then press and hold the programmed button on the transmitter to change
the brightness. Hold the button until the desired brightness is reached, then
release the button.
Press and hold the same button again on the transmitter to change the
brightness again in the opposite way. When the desired brightness is
reached, release the button.
brightness in
again,
remove the finger from the touch pad until the desired brightness is reached.
Note: Press and hold for more than 10 seconds will toggle the mode
between ON/OFF and Dimming.
If a transmitter or a sensor is programmed to the Wall Dimmer under the
flashing alert mode, when that transmitter is activated, the light connected
will flash for the predetermined timer interval.
After the timer interval, the light will
be off.
Pressing a programmed button can override flashing
alert operation.
The brightness of the light
can only be set under regular mode.
for regular mode
7. COUNTDOWN TIMER OPERATING MODE
If a transmitter or a sensor is programmed to the Wall Dimmer under the
countdown timer mode, when that transmitter is activated, the light con-
nected will be on for the predetermined timer interval.
After the timer interval, the
light will be off.
Pressing a programmed button can override countdown
timer operation.
The brightness of
the light can only be set under regular mode.
for regular mode
Use the Wall Dimmer
To turn on / off the light, simply tap the touch pad of the wall dimmer
once with your finger, it will toggle the status of the light, i.e. from on to
off or from off to on.
Note: Once the number of flashes reaches 5, it will stay at this setting. If
you would like to go back to other settings, such as 1 minute, release the
button and repeat from step 1 to start over.
Once a transmitter (button) is programmed for timer mode or flashing
mode, activating this programmed transmitter (button) will turn on the
light for the specified timer duration.
During a timer count down, if the Wall Dimmer receives another signal for
timer operation, the timer will start again and overrides the previous timer,
therefore, extending the On period by another timer interval.
To stop timer count down, press a programmed button for regular mode.
4. SET TIMER DURATION
Number of Flashes
1
2
3
4
5
Timer Duration
1 min.
5 min.
15 min.
30 min.
60 min.
As mentioned, the timer can be set to the following durations, 1 minute,
5 minutes, 15 minutes, 30 minutes, or 60 minutes.
This timer duration is used for both under Flashing Alert Operating Mode
and Countdown Timer Operating Mode.
There is only one timer setting, so all transmitters that are programmed
for timer mode and flashing mode will have the same timer duration. To
set the timer duration, follow the instructions below:
1. Wall Dimmer must be installed and powered properly. The connected
light should be off, and the 2 blue LEDs are on. The light must
be off in order to set the timer duration.
2. Press and hold the SET button for 3 seconds, the lower blue LED
flashes once. The number of flashes indicates the timer duration:
3. Continue to hold the SET button until it reaches the desired setting. The
status will change every 6 seconds, i.e. hold the SET button for another
6 seconds, you will see the number of flashes changes from 1 to 2, 2 to
3, etc.
3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS (CONT)
4. Within 15 seconds, follow steps A) to C).
A). Press the PROG button on the back of the TC transmitter with a sharp
object.
B). Press the button on the TC transmitter that you would like to program.
C). Once the transmitter is programmed, the two blue LEDs on the Wall
Dimmer flash quickly then stop flashing, indicating you have
successfully programmed the transmitter to the module. Now the
programmed transmitter button is ready to be used for Countdown
Timer Mode.
To program other transmitters/sensors, please refer to the instructions
of those transmitters/sensors and above instructions.
Note: You must complete the programming sequence within the 15-second
interval, otherwise, the Wall Dimmer will quit from programming mode and
you need to start again from step 1.
If you have a deluxe remote, you can make sure that you will actually turn
on a light by pressing [ ] first, then the programmed button. Similarly,
you can make sure that you will turn off a light by pressing [ ] first, then
the programmed button.
If you have a deluxe remote and you press [ ], all those receivers to
which the remote is programmed will turn on their loads. If you press
[ ], all those receivers to which the remote is programmed will turn
off their loads.