Sony AC VQP10 Battery Charger User Manual


 
Troubleshooting
Specifications
Input rating 100 - 240 V AC 50/60 Hz 18 W
Output rating DC OUT: 8.4 V 1.5 A (VCR)
8.4 V 1.4 A (CHARGE)
Operating temperature 0 °C to +40 °C (+32 °F to +104 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Dimensions Approx. 93 × 46 × 85 mm (w/h/d)
(3
3
/
4
× 1
13
/
16
× 3
3
/
8
inches)
Mass (AC Adaptor/Charger only) Approx. 200 g (7.1 oz)
Supplied accessories Connecting cord DK-225 (1)
AC power cord (1)
Design and specifications are subject to change without notice.
Use a commercially available AC plug adaptor, if necessary, depending on
the design of the wall outlet.
Do not connect the battery charger to a voltage adaptor (travel converter)
for overseas travel. This may result in overheating or other malfunction.
Identifying the parts
See illustration A.
1 Slot 1
2 DC OUT connector
3 CHARGE lamp 1
4 Slot 2
5 CHARGE lamp 2
6 Mode change switch
7 Display window
8 Slot indicator lamp
9 DISPLAY change button
Display window
q; “InfoLITHIUM” indicator
qa WARNING indicator
qs TIME TO CHG (charge) indicator
qd Time indicator
qf BATTERY LIFE (battery remaining time) indicator
qg VCR/CAMERA indicator
qh Full charge indicator
qj Remaining battery indicator
To Charge the Battery Pack
See illustration B-1.
1 Set the mode change switch to CHARGE.
2 Connect the power cord to this unit.
3 Connect the power cord to a wall outlet.
The beep sounds and the display window lights up.
4 Install the battery pack.
When charging starts, the battery mark in the display window will, in
order, blink and the internal CHARGE lamp on the main unit will be lit.
When charging, all of the battery marks will be lit (Normal charge).
In addition, the internal CHARGE lamp will go out; continuing to
charge until “FULL” is displayed in the battery mark (in about 1 hour)
will allow the unit to be used even longer (Full charge).
Remaining battery indicator
5When charging is complete, remove the battery pack.
Attaching two battery packs simultaneously
This unit allows attachment of two battery packs simultaneously. In this
case, charging starts with the battery pack attached in Slot 1.
When two battery packs are not attached simultaneously, charging starts
with the battery pack attached first regardless of whether it is in Slot 1
or 2.
Note
This unit cannot charge two battery packs simultaneously.
PRECAUTION
Tht set is not disconnected from the AC power source (wall outlet) as long
as it is connected to the wall outlet, even if the set itself has been turned off.
A
1
2
B
English
Notes
The time display shows the approximate time when charging at +25 °C.
The time display may differ from the actual charging time depending on
using conditions and circumstances.
The time display may show “– – – –” in the following cases. However, this
is not a malfunction.
–The remaining battery time is less than 5 minutes.
There is a difference between the displayed time and actual charging
time. Even if this happens, continue charging.
Full charge requires about 1 hour after normal charge is complete. If you
remove the battery pack between normal charge and full charge, the
charging time may not be displayed properly in the next charging.
When a battery that has not been used for a long time is charged, the
displayed remaining time and full charge time sometimes differ from the
actual times. This is not a malfunction. If this happens, charge the battery
pack until it is fully charged. The correct times can be displayed.
When you attach a fully charged battery pack to this unit, “TIME TO CHG
FULL 1h” may appear on the display. However, this is not a malfunction.
•You may wait for a while after pressing DISPLAY until the display shows
the time indication.
• To display the remaining battery time of a new battery, attach it to your
video camera recorder and use it for about 20 seconds. Then, charge the
battery with this unit.
You may wait for a while until the time display appears for the battery
pack that is not being charged. In addition, there are cases where the time
will not be displayed depending on the condition of the battery pack.
These instances are not malfunctions.
To Operate Video Equipment
See illustration C.
For details of the connection, refer to the instruction manual of the video
equipment.
1 Set the mode change switch to VCR/CAMERA.
2 Connect the power cord to this unit.
3 Connect the power cord to a wall outlet.
4 Connect the connecting cord A to the DC OUT connector of this
unit.
5Connect the connecting cord B to the video equipment.
For details of the direction of the connecting cord, refer to the instruction
manual of the video equipment.
Notes
If you set the mode change switch to CHARGE while operating the video
equipment, the power supply to the video equipment stops.
You cannot charge the battery pack attached to this unit while operating
the video equipment.
Keep this unit away from the equipment you are using if the picture is
disturbed.
Thank you for purchasing the Sony AC adaptor/charger.
Before operating the unit, please read this manual thoroughly and retain it
for future reference.
The AC-VQP10 AC adaptor/charger can be used as follows:
Connect the power cord (supplied) to a wall outlet.
To charge a lithium ion type battery pack. Ni-Cd/Ni-MH type batteries
are not rechargeable.
The following functions are available:
– Quickly charging
– Remaining charge time display
To enable the power supply to the video equipment, connection cords are
included with this unit.
What is the “InfoLITHIUM” ?
The “InfoLITHIUM” is a lithium ion battery pack which can exchange data
with compatible electronic equipment about its battery consumption. Sony
recommends that you use the P series “InfoLITHIUM” battery pack with
electronic equipment having the mark.
“InfoLITHIUM” is a trademark of Sony Corporation.
Notes on Use
About the AC power cord plug
The AC-VQP10 comes in two models, differentiated by the shape of the AC
power cord plug.
Model Shape of the plug
Model for USA/Canada Polarized
Model for other countries/regions Non polarized
The model for USA and Canada: One blade of the plug is wider than the
other for the purpose of safety and will fit into the wall outlet only one
way. If you are unable to insert the plug fully into the outlet, contact your
dealer.
About the remaining battery time
While charging the battery pack, this unit will show the remaining battery
time with your video equipment, etc. on the following conditions.
Using the “InfoLITHIUM” battery pack
Using the electronic equipment having the mark
Make sure that you use the battery pack having the mark.
Consult the operating instructions supplied with your video equipment if it
is applied to “InfoLITHIUM”.
If you use this battery pack with electronic equipment not having the
mark, the remaining battery capacity will not be indicated in minutes.*
* The indication may not be accurate depending on the condition and environment
which the equipment is used under.
Warranty for Recorded Content
Contents of the recording cannot be compensated if recording or playback
is not made due to a malfunction of the battery pack, AC power adaptor,
AC power adaptor/charger, etc.
We cannot provide compensation for image
content
We cannot provide compensation for recorded content such as images and
sound, if images are not recorded or played back due to a malfunction in
the AC adapter/charger, etc.
Charging
Use only a lithium ion type battery pack. This unit cannot be used to charge
a Ni-Cd/Ni-MH type battery pack.
Attach the battery pack firmly.
Charge the battery pack on a flat surface without vibration.
Charging temperature
To provide maximum battery efficiency, the recommended temperature
range when charging is +10 °C to +30 °C (+50 °F to +86 °F).
This unit complies with quick charging, but charging outside the
recommended temperature range will lead to longer charging times in
order to protect the battery pack. Once the charging time has been
extended, it will not return to quick charging even if the temperature is
brought within the recommended temperature range. Reattach the
battery and then recharge it.
Others
The negligible amount of electric current will flow into the AC adaptor/
charger as long as the AC adaptor/charger is plugged into the wall outlet.
Unplug the unit from the wall outlet if it will not be used for extended
period of time. To disconnect the cord, pull it out by the plug. Never pull
the cord itself.
Do not operate the unit with a damaged cord or if it has been dropped or
damaged.
Use this unit near to a wall outlet. This is to ensure that the power plug
can be immediately unplugged from the wall outlet to turn the power off
if some abnormality occurs during use.
The nameplate indicating operating voltage, power consumption, etc. is
located on the bottom.
Be sure that nothing metallic comes into contact with the metal parts of
the unit or connecting plate. If it does, a short may occur and the unit may
be damaged.
Always keep the metal contacts clean.
Do not disassemble or convert the unit.
Do not apply mechanical shock or drop the unit.
While the unit is in use, it gets warm. But this is normal.
Keep the unit away from AM receivers, because it will disturb AM
reception.
Do not place the unit in a location where it is:
— Extremely hot or cold
— Dusty or dirty
— Very humid
— Vibrating
Placing this unit in locations subject to the direct sunlight such as on
dashboards or near heating apparatus may cause this unit to deform or
malfunction.
If any difficulty should arise, unplug the unit and contact your nearest Sony
dealer.
Français
En cas de panne
Symptômes
L’appareil vidéo ne
fonctionne pas.
La batterie n’est pas
chargée.
L’alimentation est tout de
suite coupée, bien que
l’autonomie de la batterie
soit suffisante, ou le temps
restant affiché est différent
du temps actuel.
L’affichage ne change pas.
La recharge rapide est
impossible.
Le voyant CHARGE
clignote, et « CHARGE
ERROR » apparaît.
Spécifications
Alimentation 100 - 240 V CA 50/60 Hz 18 W
Tension de sortie DC OUT: 8,4 V 1,5 A (VCR)
8,4 V 1,4 A (CHARGE)
Température de fonctionnement De 0 °C à +40 °C (+32 °F à +104 °F)
Température d’entreposage De –20 °C à +60 °C (–
4 °F à +140 °F)
Dimensions Env. 93 × 46 × 85 mm (l/h/p)
Poids (Adaptateur secteur/chargeur seulement)
Env. 200 g (7,1 on.)
Accessoires fournis Cordon de liaison DK-225 (1)
Cordon d’alimentation (1)
La conception et les spécifications peuvent être modifiées sans préavis.
Utilisez, au besoin, un adaptateur de fiche secteur vendu dans le commerce
selon la configuration de la prise murale.
Si vous voyagez à l’étranger, n’utilisez pas le chargeur avec un
adaptateur de tension (adaptateur portatif). Cela peut provoquer une
surchauffe et des dysfonctionnements.
Nomenclature
Voir l’illustration A.
1 Fente 1
2 Connecteur DC OUT
3 Témoin CHARGE 1
4 Fente 2
5 Témoin CHARGE 2
6 Sélecteur de mode
7 Afficheur
8 Témoin d’indicateur de logement
9 Touche DISPLAY (changement d’affichage)
Afficheur
q; Indicateur « InfoLITHIUM »
qa Indicateur WARNING (avertissement)
qs Indicateur TIME TO CHG (recharge)
qd Indicateur de temps
qf Indicateur BATTERY LIFE (autonomie de la batterie)
qg Indicateur VCR/CAMERA (lecture/enregistrement)
qh Indicateur de recharge complète
qj Indicateur de temps restant
Pour charger une batterie
Voir l’illustration B-1.
1 Réglez le sélecteur de mode sur CHARGE.
2 Raccordez le cordon d’alimentation à cet appareil.
3 Raccordez le cordon d’alimentation à une prise murale.
Un bip retentit et l’afficheur s’allume.
4 Installez la batterie rechargeable.
Lorsque la recharge commence, l’icône de batterie dans l’afficheur
clignote d’abord puis le témoin CHARGE interne reste allumé sur
l’appareil.
Pendant la recharge, toutes les icônes de batterie sont allumées (Charge
normale).
Le témoin CHARGE interne s’éteint. Si la recharge se poursuit jusqu’à ce
que « FULL » apparaisse dans l’icône de batterie (1 heure de plus
environ), l’autonomie de la batterie sera plus longue (Charge complète).
Indicateur de charge de la batterie
5 Lorsque la recharge est terminée, retirez la batterie.
Rattachement simultané de deux batteries
Deux batteries peuvent être rattachées en même temps. Dans ce cas, la
batterie dans la fente 1 est d’abord rechargée.
Si les deux batteries ne sont pas rattachées en même temps, la recharge
commence par la première batterie rattachée même si celle-ci se trouve
dans la fente 2.
Remarque
Les deux batteries ne peuvent pas être rechargé en même temps.
PRECAUTION
L’ensemble adaptateur-camescope n’est pas isolé de la source
d’alimentation secteur tant qu’il reste branché sur la prise murale (secteur),
même si le camescope a été mis hors tension.
Pour installer la batterie rechargeable
Voir l’illustration B-2.
1 Posez la batterie sur cet appareil avec le repère
bb
bb
b orienté vers la
borne.
2 Faites glisser la batterie dans le sens de la flèche.
Poussez-la de sorte qu’elle s’encliquette.
Pour enlever la batterie rechargeable
Voir l’illustration B-2.
Faites glisser la batterie dans le sens de la flèche, puis tirez-la tout droit.
Merci pour l’achat de cet adaptateur secteur/chargeur Sony.
Avant d’utiliser cet appareil, lisez cette notice avec attention et conservez-la
pour toute référence future.
L’adaptateur secteur/chargeur AC-VQP10 peut être utilisé de la façon
suivante:
Le cordon d’alimentation (fourni) doit être raccordé au préalable à une
prise murale.
Pour recharger une batterie rechargeable au lithium-ion. Les batteries Ni-
Cd/Ni-MH ne sont pas rechargeables.
Les fonctions suivantes seront disponibles:
– Recharge rapide
– Affichage du temps de charge restant
Pour alimenter un appareil vidéo (les cordons de liaison sont fournis avec
cet appareil).
Qu’est-ce qu’une batterie « InfoLITHIUM » ?
Une batterie « InfoLITHIUM » est une batterie rechargeable au lithium-ion
pouvant échanger des données sur la consommation d’énergie avec un
appareil électronique compatible. Sony recommande d’utiliser les modèles
P de batterie « InfoLITHIUM » avec les appareils électroniques portant la
marque .
« InfoLITHIUM » est une marque commerciale de Sony Corporation.
AVERTISSEMENT
Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution, garder le coffret fermé.
Ne confier l’entretien de l’appareil qu’à un technicien qualifié.
Le cordon d’alimentation secteur de l’appareil doit être changé par un
professionnel uniquement.
Remarques sur l’utilisation
Fiche du cordon d’alimentation secteur
Le modèle AC-VQP10 existe en deux versions, qui se différencient par la
fiche du cordon d’alimentation secteur.
Modèle Forme de la fiche
Modèle pour les Etats-unis
Polarisée
et le Canada
Modèle pour les autres pays
Non polarisée
ou régions
Modèle pour les Etats-Unis ou le Canada: Une des lames de la fiche est
plus large que l’autre pour des raisons de sécurité et ne peut s’insérer que
dans un sens. Si vous ne parvenez pas à insérer complètement la fiche
dans la prise, contactez votre revendeur.
Indication d’autonomie
Pendant la recharge de la batterie, cet appareil indiquera l’autonomie de
l’appareil vidéo, etc. dans les cas suivants:
Vous utilisez une batterie « InfoLITHIUM »
Vous utilisez un appareil électronique utilisant la marque
Assurez-vous que la batterie que vous utilisez porte la marque
.
Consultez le mode d’emploi fourni avec votre appareil vidéo s’il s’agit d’un
appareil « InfoLITHIUM ».
Si vous utilisez la batterie « InfoLITHIUM » avec des appareils électroniques ne
portant pas la marque
, l’autonomie de la batterie ne sera pas indiquée
en minutes.*
* Il se peut que l’indication ne soit pas précise. Cela dépend de la situation et de
l’environnement dans lesquels l’appareil est utilisé.
Garantie concernant l’enregistrement
Aucune compensation ne peut être accordée si l’enregistrement ou la
lecture n’a pas pu être effectué en raison d’un problème de batterie,
d’adaptateur secteur ou d’adaptateur secteur/chargeur, etc.
Aucune compensation en cas de perte
d’images
Aucune compensation ne peut être accordée si l'enregistrement ou la
lecture (images ou son) n’ont être effectuées en raison d’un mauvais
fonctionnement de l’adaptateur secteur/chargeur, etc.
Recharge
N’utilisez que des batteries au lithium-ion avec l’adaptateur. L’adaptateur
ne peut être utilisé pour charger une batterie au Ni-Cd/Ni-MH.
Fixez bien la batterie.
Chargez la batterie sur une surface plane et sans vibrations.
Temps de recharge
Pour tirer le meilleur parti de la batterie, il est conseillé de la recharger
à une température de +10 °C à +30 °C (+50 °F à +86 °F).
•Cet appareil permet des recharges rapides, mais hors de la plage de
températures spécifiée, les temps de recharge sont plus longs pour
protéger la batterie. Lorsque le temps de recharge a été prolongé, il
n’est pas possible de faire une recharge rapide même si la température
ambiante augmente. Il faut remettre la batterie en place et la recharger
une nouvelle fois.
Divers
Une quantité négligeable d’électricité circule dans l’adaptateur secteur/
chargeur s’il reste branché sur la prise murale.
Débranchez l’appareil de la prise murale si vous n’avez pas l’intention de
l’utiliser pendant un certain temps. Pour débrancher le cordon secteur,
tirez sur la fiche. Ne tirez jamais sur le cordon.
N’utilisez pas l’appareil lorsque le cordon est endommagé, ou si
l’adaptateur est tombé ou a été endommagé.
Utilisez cet appareil près d’une prise murale. Vous pourrez débrancher
immédiatement la fiche de la prise murale pour éteindre l’appareil en cas
d’anomalie.
La plaque signalétique indiquant la tension de fonctionnement, la
consommation électrique et d’autres informations électriques se trouve
sous l’appareil.
Evitez que des objets métalliques ne touchent les parties métalliques de
l’appareil ou de la plaque de connexion. Un court-circuit pourrait se
produire et endommager l’appareil.
Veillez à ce que les contacts soient toujours propres.
Ne pas démonter ni modifier l’appareil.
Ne pas appliquer de chocs mécaniques à l’appareil ni le laisser tomber.
Quand l’appareil est utilisé, il devient chaud. C’est tout à fait normal.
Ne pas laisser l’appareil près d’un récepteur AM, car il perturbera la
réception AM.
Ne pas entreposer l’appareil dans les endroits suivants:
— extrêmement chauds ou froids
— poussiéreux ou sales
— très humides
— exposés à des vibrations.
N’exposez pas cet appareil à la lumière directe du soleil, comme sur le
tableau de bord d’une voiture, ni à la chaleur d’un appareil de chauffage,
car il pourrait être déformé ou ne plus fonctionner.
En cas de problème, débranchez l’appareil et contactez votre revendeur Sony.
Remarques
Ne saisissez pas l’adaptateur secteur/chargeur par la batterie lorsqu’elle
est installée dessus.
•Faites particulièrement attention de ne pas cogner la batterie lorsque vous
l’installez.
Faites attention de ne pas vous coincer les doigts lorsque vous rattachez
ou retirez la batterie.
Temps de recharge
Le tableau suivant indique le temps de recharge quand la batterie
principale est complètement déchargée.
Temps approximatif en minutes, nécessaire pour recharger complètement
une batterie vide (Temps de charge complète).
Les minutes entre parenthèses indiquent le temps de recharge normale
(Temps de charge normale).
Voir le mode d’emploi de l’appareil vidéo utilisé pour l’autonomie de la
batterie.
Le temps de recharge varie selon l’état de la batterie et la température
ambiante.
Remarques
•Si vous réglez le sélecteur de mode sur VCR/CAMERA pendant la
recharge, la recharge s’arrêtera.
Si le témoin CHARGE ne s’allume pas ou clignote, vérifiez que la batterie
est fixée correctement à l’adaptateur secteur/chargeur. Si elle n’est pas
rattachée correctement, elle ne se rechargera pas.
Indication des temps
Pendant la recharge, vous pouvez vérifier le temps de recharge sur la
fenêtre d’affichage. Une minute après le début de la recharge, BATTERY
LIFE s’allume. Le temps indiqué désigne l’autonomie de la batterie lorsque
vous prenez des photos avec le viseur. L’autonomie sera plus courte si vous
utilisez l’écran LCD.
Appuyez sur DISPLAY pendant la recharge
Après avoir rattaché la batterie, attendez environ 1 minute. A chaque
pression de DISPLAY, le témoin de fente s’allume et l’affichage suivant
apparaît sur l’afficheur.
Si deux batteries sont rattachées en même temps, l’indication de la batterie
qui n’est pas rechargée est automatiquement remplacé par l’indication du
temps de la batterie rechargée dans les 10 secondes qui suivent.
L’exemple suivant montre les temps indiqués lorsqu’une première batterie
est insérée dans la fente 1 et une seconde dans la fente 2. Le témoin de
fente correspond au numéro de fente.
Causes/Solutions
Le cordon d’alimentation est débranché de la
prise murale.
t Rebranchez-le sur la prise murale.
•Le cordon de liaison n’est pas branché
correctement.
t Raccordez-le correctement.
Le sélecteur de mode est réglé sur CHARGE.
t Réglez-le sur VCR/CAMERA.
Le sélecteur de mode n’est pas réglé sur
VCR/CAMERA.
t Réglez-le sur CHARGE.
Rechargez une nouvelle fois la batterie
complètement.
t L’autonomie n’est pas indiquée
correctement.
t Voir « Indication d’autonomie ».
L’affichage suivant peut apparaître si la
batterie est rechargée hors de la plage de
températures recommandée (+10 °C à +30 °C).
Dans ce cas, la recharge est possible mais elle
est plus longue pour protéger la batterie.
t Consultez le tableau suivant.
5
To remove
Pour retirer
WARNING
BATTERY LIFE
TIME TO CHG
NORMAL FULL
hm
VCR/CAMERA
q;
qa
qs
qd
q
f
qg
qh
qj
Retirez la batterie de l’appareil, puis remettez-la en place.
Si le témoin CHARGE
clignote encore:
Installez une autre batterie.
Si le témoin CHARGE s’allume et ne
clignote plus:
Si le témoin CHARGE s’éteint parce
que la batterie a été rechargée, c’est
normal.
Si le témoin CHARGE
clignote encore:
Le problème vient de cet
appareil.
Veuillez contacter votre revendeur Sony et lui apporter l’appareil qui ne
fonctionne pas.
Si le témoin CHARGE s’allume et
ne clignote plus:
Si le témoin CHARGE s’éteint parce
que la batterie a été rechargée, le
problème vient de la première
batterie installée.
Adaptateur de fiche secteur
Prise murale
AC-VQP10
Charge normale Charge complète
Remarques
Le temps indiqué est approximatif même quand la batterie est rechargée
entre +25 °C. Selon les conditions d’utilisation et les circonstances, le
temps peut être différent du temps réel.
•« – – – – » peut apparaître sur la fenêtre d’affichage dans les cas suivants.
Il ne s’agit pas d’une anomolie.
L’autonomie de la batterie est inférieure à 5 minutes.
Il y a une différence entre le temps affiché et le temps de recharge réel.
Continuez la recharge, si cet indicateur apparaît.
Une recharge complète prend environ une heure. Si vous détachez la
batterie entre la recharge normale et la recharge complète, le temps risque
de ne pas être indiqué correctement lors de la recharge suivante.
Si une batterie n’a pas été utilisée pendant longtemps, l’autonomie
indiquée et le temps de recharge complète peuvent être inexacts. C’est
normal. Dans ce cas, rechargez une nouvelle fois la batterie. Les temps
seront alors corrects.
Quand vous raccordez une batterie complètement rechargée à cet
appareil, « TIME TO CHG FULL 1h »peut apparaître sur la fenêtre
d’affichage. Il ne s’agit pas d’une anomolie.
Il faut attendre un certain temps après une pression de DISPLAY pour
que le temps apparaisse.
•Pour connaître l’autonomie d’une batterie neuve, insérez-la sur l’appareil
vidéo et utilisez-la pendant 20 secondes environ. Rechargez ensuite la
batterie sur cet appareil.
•Il faut attendre un certain temps pour que le temps de la batterie qui n’est
pas rechargée soit indiqué. En outre, dans certain cas, le temps n’est pas
indiqué. Ceci dépend de l’état de la batterie, ce n’est pas une anomalie.
Pour utiliser l’appareil vidéo
Voir l’illustration C.
Pour le détail sur la connexion, reportez-vous au mode d’emploi de
l’appareil vidéo.
1Réglez le sélecteur de mode sur VCR/CAMERA.
2Raccordez le cordon d’alimentation à cet appareil.
3Raccordez le cordon d’alimentation à une prise murale.
4 Raccordez le cordon de liaison A au connecteur DC OUT de cet
appareil.
5 Raccordez le cordon de liaison B à l’appareil vidéo.
Pour le détail sur le sens du cordon de liaison, voir le mode d’emploi de
l’appareil vidéo.
Remarques
Si vous réglez le sélecteur de mode sur CHARGE pendant l’utilisation de
l’appareil vidéo, l’alimentation sera coupée.
Vous ne pouvez pas recharger la batterie quand elle est sur l’appareil
vidéo et que celui-ci bonctionne.
Eloignez l’adaptateur de l’appareil vidéo s’il perturbe l’image.
Temps restant jusqu'à la
fin d’une recharge
normale de la première
batterie rattachée
Le temps d’une recharge
normale n’est pas indiqué
lorsque la recharge est
terminée.
Temps restant jusqu'à la
fin d’une recharge
complète de la première
batterie rattachée
Le temps de recharge
complète n’est pas affiché
lorsque la recharge complète
est terminée.
Autonomie de la
batterie lorsque la
dernière batterie
rattachée est installée
sur l’appareil
électronique
« InfoLITHIUM »
L’autonomie n’est pas
indiquée lorsque l’autonomie
est inférieure à 5 minutes.
Temps restant jusqu'à la
fin d’une recharge
normale de la dernière
batterie rattachée
Le temps de recharge normal
n’est pas indiqué lorsque la
recharge normale est
terminée.
Temps restant jusqu'à la
fin d’une recharge
complète de la batterie
rattachée
Le temps de recharge
complète n’est pas indiqué à
la fin de la recharge complète.
Indication de
l’autonomie de la
batterie lorsque la
première batterie
rattachée est installée
sur l'appareil
électronique
« InfoLITHIUM »
Le temps n’est pas indiqué
lorsque l’autonomie est
inférieure à 5 minutes.
1
2
1
2
1
2
1
2
1
2
1
2
Batterie dans la fente 1 seulement
Batteries dans les fentes 1 et 2
To Install the battery pack
See illustration B-2.
1 Place the battery pack on this unit with the
b b
b b
b mark facing the
terminal.
2 Slide the battery pack in the direction of the arrow.
Slide it in until you hear a click.
To remove the battery pack
See illustration B-2.
Slide the battery pack in the direction of the arrow, then lift it straight out.
Notes
Do not pick up the AC adaptor/charger by the battery pack when there is
a battery pack installed.
Be particularly careful not to hit the battery when installing it.
Be careful not to pinch your fingers during attachment and removal of the
battery pack.
Charging time
The following table shows the charging time for the main battery pack
which is discharged completely.
Approximate minutes to charge an empty battery pack fully (Full
charging time).
Approximate minutes in parentheses indicate the time when you charge
normally (Normal charging time).
To ascertain the battery life, refer to the instruction manual of the video
equipment which you use.
The charging time may differ depending on the condition of the battery
pack or the temperature of the environment.
Notes
When the mode change switch is set to VCR/CAMERA during charging,
charging stops.
If the CHARGE lamp does not light or flash, check that the battery pack is
correctly attached to the AC adaptor/charger. If it is not attached it will
not be charged.
To Check Charging
While charging, you can check the charging time on the display. After
starting charging in a minute, BATTERY LIFE lights up on the display.
The displayed remaining time is the approximate time when taking
photographs via the viewfinder. The remaining time is shorter when the
LCD display is used.
Press DISPLAY while charging is underway.
After attaching a battery pack, wait for about 1 min. Each time you press
DISPLAY, the slot indicator lamp lights up and the display in the display
window changes to the display shown below.
When two battery packs are attached simultaneously, the time display of
the battery pack not being charged will automatically return to the time
display of the battery pack being charged after about 10 seconds.
Here is an example of installation of a battery pack in Slot 1 first and then
in Slot 2. The slot indicator lamp corresponds to the slot number.
Symptom
Video equipmet does not
work.
The battery is not charged.
Power immediately turns
off even though there is
sufficient remaining battery
power, or the displayed
remaining time differs from
the actual time.
The display is not switched.
The rapid charging is not
performed.
The CHARGE lamp blinks,
and “CHARGE ERROR” is
displayed in the display
window.
Cause/Solution
The power plug is disconnected from the
wall outlet.
t Insert into the wall outlet.
The connector cable is not properly connected.
t Connect properly.
The mode change switch is set to CHARGE.
t Set the mode change switch to VCR/
CAMERA.
The mode change switch is set to VCR/
CAMERA.
t Set the mode change switch to CHARGE.
Fully charge again.
t The remaining battery power will be
correctly displayed.
t Read “About the remaining battery time”.
The display shown below may appear if a
battery pack is charged outside of the
recommended charging temperature range of
+10 °C to +30 °C. In this case, charging can be
performed, but it will not be performed with
quick charging to protect the battery pack.
t Check through the following chart.
Normal charge Full charge
Battery pack Full charging time Normal charging time
NP-FP50 125 (65)
NP-FP70 130 (70)
NP-FP90 175 (115)
The remaining time until
normal charge of the
first attached battery
pack is complete
The normal charge time is not
displayed after the normal
charge is complete.
The remaining time until
full charge of the first
attached battery pack is
complete
The full charge time is not
displayed after the full charge
is complete.
The remaining battery
time when the last
attached battery pack
will be installed in your
“InfoLITHIUM” electronic
equipment
The time is not displayed
when the remaining battery
time is less than 5 minutes.
The remaining time until
normal charge of the
last attached battery
pack is complete
The normal charge time is not
displayed after the normal
charge is complete.
The remaining time until
full charge of the last
attached battery pack is
complete
The full charge time is not
displayed after the full charge
is complete.
The remaining battery
time when the first
attached battery pack
will be installed in your
“InfoLITHIUM” electronic
equipment
The time is not displayed
when the remaining battery
time is less than 5 minutes.
1
2
1
2
1
2
1
2
1
2
1
2
A battery pack attached only in Slot 1
Two battery packs attached in Slot 1 and Slot 2
Remove the battery pack from this unit, then install the same battery pack
again.
If the CHARGE lamp blinks
again:
Install another battery pack.
If the CHARGE lamp lights and
does not blink again:
If the CHARGE lamp goes out
because the charging time has
passed, there is no problem.
If the CHARGE lamp blinks
again:
The problem is with this unit.
If the CHARGE lamp lights and
does not blink again:
If the CHARGE lamp goes out
because the charging time has
passed, the problem is with the
battery pack first installed.
Please contact your nearest Sony dealer in connection with the product
with the problem.
2
44
3
1
C
2
4
3
1
1 Slot 1
Fente 1
2 DC OUT connector
Connecteur DC OUT
3 CHARGE lamp 1
Témoin CHARGE 1
4 Slot 2
Fente 2
5 CHARGE
lamp 2
Témoin
CHARGE 2
7 Display window
Afficheur
8 Slot indicator lamp
Témoin d’indicateur
de logement
9 DISPLAY
change button
Touche
DISPLAY
(changement
d’affichage)
6 Mode change
switch
Sélecteur
de mode
A
B
Batterie Temps de Temps de
rechargeable charge complète charge normale
NP-FP50 125 (65)
NP-FP70 130 (70)
NP-FP90 175 (115)
AC plug adaptor
AC-VQP10
Wall outlet
To install
Pour installer
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet.
Refer servicing to qualified personnel
only.
NOTICE FOR THE CUSTOMERS IN THE U.S.A AND CANADA
This symbol is intended to alert the user to the presence
of uninsulated “Dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
The Graphical Symbols with Supplemental Marking is located on the
bottom of the unit.
NOTICE FOR THE CUSTOMERS IN THE U.S.A
CAUTION
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
NOTICE FOR THE CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS 1363 is fitted to this equipment for
your safety and convenience.
Should the fuse in the plug supplied need to be replaced, a fuse of the
same rating as the supplied one and approved by ASTA or BSI to BS1362
(i.e., marked with or mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be
sure to attach the fuse cover after you change the fuse. Never use the
plug without the fuse cover. If you should lose the fuse cover, please
contact your nearest Sony service station.
AC Adaptor/Charger
Operating Instructions
Mode d’emploi
Manual de instrucciones
3-089-860-11(1)
AC-VQP10
© 2004 Sony Corporation Printed in Japan
Owner’s Record
The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer
regarding this product.
Model No. AC-VQP10 Serial No.
SERIES
TM
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.