Bostitch LPF21PL Nail Gun User Manual


 
MAINTAINING THE TOOL
When working on air tools note the warnings in this manual and use extra care when
evaluating problem tools.
TOOL SPECIFICATIONS
A
ll screws and nuts are metric.
FASTENER SPECIFICATIONS:
LPF21PL:
- Uses 21° plastic collated full round head stick nails, in lengths of 2” to 3-1/4” (50-83 mm) and shank diameters of
0.113” to 0.148” (2.8 - 3.8 mm)
LPF33PT:
- Uses 30°-34° paper tape collated clipped head or offset round head stick nails, in lengths of 2” to 3-1/4”
(50-83 mm) and shank diameters of 0.113” to 0.131” (2.8 - 3.3 mm)
LPF28WW:
- Uses 28° wire collated notched head or offset round head stick nails, in lengths of 2" to 3-1/4" (50-83mm) and
shank diameters of .113" to .131" (2.8 - 3.3mm)
TOOL AIR FITTING:
This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .275” (7 mm) or larger. The fitting must be
capable of discharging tool air pressure when disconnected from the air supply.
OPERATING PRESSURE:
70 to 120 p.s.i.g. (4.9 to 8.4 kg/cm
2
). Select the operating pressure within this range for best fastener performance.
DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
AIR CONSUMPTION:
The LPF21PL / LPF33PT / LPF28WW requires 7.5 cubic feet per minute (212 liters per minute) of free air to
operate in sequential trip mode at the rate of 100 nails per minute, at 80 p.s.i.g (5.6 kg/cm²). Take the actual rate at
which the tool will be run to determine the amount of air required. For instance, if your fastener usage averages 50
nails per minute, you need 50% of the 7.5 c.f.m. (212 liters per minute) which is required to operate the tool at 100
nails per minute.
OPERATING MODES
BOSTITCH OFFERS TWO MODES OF OPERATION FOR THIS TOOL.
SEQUENTIAL TRIP:
The Sequential Trip requires the operator to hold the tool against the work surface before pulling the trigger. This
makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications.The
Sequential Trip allows exact fastener placement without the possibility of driving a second fastener on recoil, as
described under “Contact Trip”. The Sequential Trip Tool has a positive safety advantage because it will not
accidentally drive a second fastener if the tool is contacted against the work – or anything else – while the operator
is holding the trigger pulled.
CONTACT TRIP:
The common operating procedure on “Contact Trip” tools is for the operator to contact the work surface to
actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is
contacted. This will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet
assembly. All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the
trip, and if unintentionally allowed to re-contact the work surface with the trigger still actuated (finger still holding
trigger pulled) an unwanted second fastener will be driven.
4
MODEL TOOL ACTUATION LENGTH HEIGHT WIDTH WEIGHT
LPF21PL
S
electable sequential/
contact trip
20-1/2” (521 mm) 12” (305 mm) 4-3/4” (121 mm) 7.6 lb. (3.45 kg.)
LPF33PT
S
electable sequential/
contact trip
17-1/2” (444 mm) 12-1/2” (318 mm) 4-3/4” (121 mm) 7.6 lb. (3.45 kg.)
LPF28WW
Selectable sequential/
contact trip
19-1/2" (495 mm) 12" (305 mm) 4-3/4" (121 mm) 7.7 lb. (3.5 kg.)
LPF21PL-LPF33PT-LPF28WW_9R189680RC_BOS_MAN_JM_166762RevC_FSeries_Man.qxd 11/26/12 10:29 AM