Operation Guide 4706
3
World Time City Code List
City
code
City Name
UTC
Offset
Applicable Cities
– – – –11 Pago Pago
HNL Honolulu –10 Papeete
ANC Anchorage –9 Nome
LAX
Los Angeles –8 San Francisco, Las Vegas, Seattle
DEN Denver –7 El Paso, Edmonton
CHI Chicago –6 Houston, Mexico City
NYC New York –5 Montreal, Miami, Boston
CCS* Caracas –4 Santiago
RIO Rio de Janeiro –3 Sao Paulo, Buenos Aires
– – – –2
– – – –1 Azores
GMT 0 Greenwich Mean Time
LON London 0 Dublin
PAR Paris +1 Rome, Madrid, Frankfurt
CAI Cairo
+2 Athens, Helsinki, Beirut
JRS Jerusalem
JED Jeddah +3 Kuwait, Moscow
THR Tehran +3.5
DXB Dubai +4 Abu Dhabi
KBL Kabul +4.5
KHI Karachi +5
DEL Delhi +5.5
DAC Dhaka +6
RGN Yangon +6.5
BKK Bangkok +7 Jakarta, Hanoi
HKG
Hong Kong
+8
Singapore, Kuala Lumpur, Beijing,
Taipei, Manila
TYO Tokyo +9 Seoul, Pyongyang
ADL Adelaide +9.5
SYD Sydney +10 Guam
NOU Noumea +11 Port Vila
WLG Wellington +12 Christchurch
The contents of the above table are current as of June 2005. •
Time differentials in the above table are in accordance with Universal •
Time Coordinated (UTC).
The rules governing offsets and summer time are determined by each •
individual country.
* In December 2007, Venezuela changed its offset from – 4 to – 4.5. Note,
however, that this watch displays an offset of – 4 (the old offset) for the
CCS (Caracas, Venezuela) city code.
Using the Alarm and Hourly Time Signal
Use C to enter the Alarm Mode.
Your watch has five alarms, which can be configured independently of
each other. The watch beeps for about 20 seconds when an alarm time
is reached. The Hourly Time signal causes the watch to beep every hour
on the hour.
Alarms and the hourly time signal all operate in accordance with the •
digital time of the currently selected Home City.
To set an alarm time
In the Alarm Mode, use 1.
D to cycle through
the alarm screens in the sequence shown
below until the one you want to set is
displayed.
!LARM !LARM !LARM
(OURLY4IME3IGNAL !LARM !LARM
Hold down 2. A for about two seconds until
the hour digits of the alarm time start to flash.
The currently displayed alarm will turn •
on automatically at this point, which is
indicated by the ALM indicator appearing
on the display.
Use 3.
C to move the flashing between
settings as shown below.
Use 4. D (+) and B (–) to change the
flashing setting.
Holding down either button scrolls at high •
speed.
Repeat steps 3 and 4 to set the alarm
time you want.
When setting the hour, make sure that AM (A) or PM (P) is specified •
correctly when using 12-hour timekeeping, or that the correct 24-hour
time is specified.
The same 12-hour/24-hour format you select for the Timekeeping •
Mode time is also applied in the Alarm Mode.
After the setting is the way you want, press 5. A to exit the setting
screen.
The watch also will exit the editing screen automatically if you do not •
perform any operation for about two or three minutes.
To turn an alarm or the hourly time signal on or off
In the Alarm Mode, use 1. D to display the screen for an alarm or for the
hourly time signal.
Press 2. A to toggle the alarm or hourly time signal on or off.
Turning on an alarm causes the ALM indicator to appear on the display. •
Turning on the hourly time signal causes the SIG indicator to appear.
(OURLY4IME3IGNAL3CREEN
6,*LQGLFDWRU
!LARM3CREEN
$/0LQGLFDWRU
To stop the alarm beeper
Press any button.
To test the alarm
In the Alarm Mode, hold down D for about two seconds to sound the
alarm.
Using the Countdown Timer
Use C to enter the Countdown Timer Mode.
You can set the start time of the Countdown Timer in units of one minute
in the range of 1 minute to 24 hours. The watch beeps for 10 seconds
when the end of the countdown is reached.
To set the Countdown Timer start time
In the Countdown Timer Mode, hold down 1.
A for about two seconds until the hour digits
of the start time start to flash. This is the
setting screen.
Use 2. C to move the flashing between
settings as shown below.
3. Use D (+) and B (–) to change the flashing
setting.
Holding down either button scrolls at high •
speed.
Repeat steps 2 and 3 to set the
Countdown start time you want.
• To configure the setting to countdown 24
hours, set the start time as 0:00.
After the setting is the way you want, press 4.
A to exit the setting screen.
The watch also will exit the setting screen automatically if you do not •
perform any operation for about two or three minutes.
To use the Countdown Timer
In the Countdown Timer Mode, press D.
Each press of • D starts or stops the
countdown.
The time is counted down in one-second •
steps.
Pressing • A while the countdown is stopped
will reset to the countdown start time.
Pressing • D again while the timer countdown is stopped will restart the
countdown.
Time Up Alert
The watch beeps for 10 seconds when the end of the countdown is
reached.
To stop the time up alarm
Press any button.
Using the Stopwatch
Use C to enter the Stopwatch Mode.
The stopwatch measures elapsed time in units of 1/100 second up
to 59 minutes, 59.99 seconds (60 minutes). When the maximum limit
is reached, the elapsed time returns to zero automatically and timing
continues from there.
To start or stop an elapsed time operation
In the Stopwatch Mode, press D to start and
stop elapsed time measurement.
Pressing • A while an elapsed time operation
is in progress will freeze the current split time
on the display and continue timing of the next
split internally. This is indicated by the SPLIT
indicator on the display.
Changing to another mode while a split time •
is displayed cancels the split time operation.
• Pressing A while timing is stopped resets the stopwatch to all zeros.
0LQXWH+RXU
6HFRQG
3TART
3TOP
2ESET
0LQXWH 6HFRQG
VHFRQG
3TART
3TOP
3PLIT
2ESET
4OMEASUREELAPSEDTIME
3TART
3TOP 2ESET
