A SERVICE OF

logo

Open as PDF
next previous
INSTALLATION
1. Usethepredrilledmountingholesinthemanifoldbracketasguides.Markanddrillanchorholes.
Mountsecurely.SeeFigures1-4.
2. Shutoffpowertomachine.
3. ConnectoutletportofInsuricesystemtoequipmentserved.AlwaysuseaNSFapprovedpipedope
orTeontapeatallconnections.Useabackupwrenchonallttingswhileconnectingtoavoid
excessive stress on the system components.
Note: If the optional E-Series Filter is used, install a manual shut-off valve leading to the system
for servicing.
4. Connectminimum3/8”waterlinetoinletsideofInsuricesystem.
5 Connecttubingtoushingvalveandruntodrain.
Note: Some municipal plumbing codes and good sanitary practices require an air gap at the drain
termination point.
6. Installthecartridge(s)intotheInsuricesystemhead(s)followingdirectionsonthecartridgelabelor
asshownintheCartridgeChangeillustrations.
7. Turnonwatertolterandcheckforleaks.
8. Flushthecartridgebyrunningwaterthroughatfullforceforveminutes.Thiswillsettheltering
mediaandpurgeairandnes,insuringmaximumlterlife.
9. Afterushing,closetheushingvalve,turnonpowertoequipmentandplugtheLPA(ifso
equipped)intotheelectricaloutlet.Seeillustrations.
CARTRIDGE CHANGE DETERMINATION
Replacecartridgeswhencapacityisreached,orwhenowbecomesinadequate,butatleastannually.
Allcartridgesonmultiplecartridgesystemsshouldbechangedatthesametime.TheEverpure
PressureGaugeorEverguardLowPressureAlarmprovidesaquickandsimplemeansofdetermining
whentheltercartridge(s)shouldbechanged.Installedontheoutletportofthelter,thegauge
orEverguardLPAcanbeusedtomeasurebothdynamic(owing)andstatic(line)pressure.The
cartridge(s)shouldbechangedwhenthepressuregaugeneedleisintheredareawhileequipment
isinoperation,andyettheneedleshowsadequatelinepressurebetweencycles.Observetheneedle
duringthenextequipmentoncycle.Iftheneedleregistersadequatepressure,itcanbeassumedthat
thetemporarylow-pressureconditionwascausedbyabriefpowerfailureorotherincomingpressure
disruption.
FLUSHING
For maximum life, all carbon filter cartridges must be flushed for five minutes at full flow before use. ALL
NEW CARTRIDGES MUST BE FLUSHED AFTER EACH CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!
Ifthecartridgesarenew,havebeenproperlyushedandbothneedleandfollowerregisterinadequatepressure,or
theLPAissounding,youmaybeexperiencinginadequatewaterpressureorsomerestrictionmayexistintheinlet
waterline.Ineithercase,theincomingwaterpressuremustbeimprovedtoreceiveoptimumlterlife.
COMPLETECARTRIDGECHANGEINSTRUCTIONSCANBEFOUNDONTHEFILTERCARTRIDGELABEL.
Not for residential use. For food service applications only.
Figure5–InsuriceSingleSystem
OUTLET
3/8" FNPT
INLET
3/8" FNPT
27.50"
5.60"
Figure6–InsuriceTwinSystem
16.60"
OUTLET
3/4" FNPT
INLET
3/4" MNPT
25.26"
Figure8–InsuriceQuadSystem
24.60"
OUTLET
3/4" FNPT
INLET
3/4" MNPT
29.69"
Figure7–InsuriceTripleSystem
21"
OUTLET
3/4" FNPT
INLET
3/4" MNPT
29.26"
Checkforcompliancewithstateandlocallaws
andregulations.Donotusewithwaterthatis
microbiologicallyunsafeorofunknownqualitywithout
adequatedisinfectionbeforeorafterthesystem.Systems
certiedforcystreductionmaybeusedondisinfected
watersthatmaycontainlterablecysts.