64
5-2 MENU SWITCH SETTING CONTENT
5 MENU SWITCH SETTING DETAILS
[ ] : Factory setting
Menu SW On-screen Counter On-screen
No. display display display
512 MUTING/ALARM [0] [OFF]
MESSAGE 1 ON
513 EDIT ON 0 OFF
SCREEN [1] [ON]
601 V.BLANK MASK 0 OFF
[1] [ON]
2 ON WITH
0.5H
620 DUBBING LOOP [0] [OFF]
13 TIMES
25 TIMES
3 10 TIMES
Selects whether “MUTING” or “CONDITION
ALARM” messages appear On-Screen.This menu
makes it easier to check the VCR’s operation
status.
The on-screen display is shown on the monitor
connected to the [VIDEO MONITOR OUT]
connector.
OFF:The “MUTING” and “CONDITION ALARM”
are not displayed.
ON :The “MUTING” and “CONDITION ALARM”
are displayed.
For more details, refer to the “MUTING/
CONDITION ALARM” display on page 24.
Selects whether the edit on-screen display is ON or
OFF during editing. On-screen information is output
from the [LINE2 SUPER OUT] connector.
OFF:Does not show the edit on-screen display
during editing.
ON :Show the edit on-screen display during
editing.
<TBC. FRAME MEMORY>
Enables/disables masking of the vertical interval.
OFF :No masking.
ON :Masks the vertical interval.
ON WITH 0.5H:Masks section for 0.5H in addition
to the vertical interval (analog
signals only).
*When this menu is set to “OFF”, only the
recordable sections of the signals output for V.
blanking in the EE mode are output (VITC,
EXTRA LINE, EXTENSION LINE).
When this menu is set to “ON”, VITC and EXTRA
LINE have priority in each menu setting (refer to
page 89).
Selects whether or not the multi-generation test
“Dubbing Loop Function” is used to aid adjusting an
analog component system to unity gain. When this
mode is active, the VCR automatically switches to
its internal color bar generator and continuously
builds the number of generations selected.
OFF : The dubbing loop function is disabled.
3 TIMES : The dubbing loop function repeatedly
builds 3 generations every few seconds.
5 TIMES : The dubbing loop function repeatedly
builds 5 generations every few seconds.
10 TIMES: The dubbing loop function repeatedly
builds 10 generations every few
seconds.
*When set to any setting except OFF (0), this unit
enters the Dubbing Loop mode.
*For more details on the dubbing loop function,
refer to page 122.
Item
Content
Setting
65
6 PREPARATION
6-1 OPERATION MODE LOCK
This unit is provided with an operation mode lock facility. This function prevents accidental changes to switch and
control settings. When this function is ON, currently selected modes and knob or switch positions cannot be
adjusted.
● Use menu switch No. 002 <OPERATION LOCK> to enable this function.
● With this function enabled, operation of all front panel control buttons, adjustment knobs, dials and switches is
disabled and changes to menu switch settings are not possible. When this function is activated, it is not possible
to change menu switch settings. However, the [PHONES LEVEL] control and menu switch No. 002
<OPERATION LOCK> (to release the operation mode lock function) can be used.
Procedure
1. Make all desired settings and operate as usual.
2. Engage the operation lock function.
Press the [MENU] button to call up the menu setting display.
Turn the jog dial and select menu switch No. 002 <OPERATION LOCK>.
If the Direct Access facility is ON, press the [STAND BY] button to call up the
menu item display more quickly.
Select “ON (1)” by turning the jog dial while pressing the [SEARCH] button.
Press the [SET] button.
The operation lock function is ON.
After the SET indication blinks for several seconds, the normal counter and
on-screen displays are restored.
3. To cancel the operation mode lock facility, set menu switch No. 002
<OPERATION LOCK> to “OFF (0)”.
