1
TROUBLESHOOTING
Before requesting service for this unit, check the table below for a possible cause of the problem
ou are experiencing.
Some simple checks or a minor adjustment on
our part ma
eliminate the problem and restore proper operation
Symptom Remedy
POWER
e power
oes not turn on
• C
ec
t
at t
e AC power cor
is connecte
secure
• Remote Contro
atteries ma
e wea
, rep
ace t
em wit
new ones
Leave the unit unplugged
or 20-30 min, plug the unit back in. I
the unit
does not power on please contact our customer service center
or service
on t
e mo
e
he unit turns on automaticall
without an
operation
• The unit turns on automaticall
2 seconds before the timer recording
Language
menu appears ever
time
the
ower turns on
• The unit ma
not have been turned off correctl
. Finish up the language setting
procedure b
selecting a language in
an
ua
e
m
n
Pr
K
iv
h
settin
, t
en press
STANDBY/ON
to turn t
e unit to t
e stan
mo
e.
Do not disconnect the AC power cord be
ore placing the unit in the standb
mode
GENERAL
T
e unit
oes not response
•
” or error message appears i
the operation is prohibited
• Remote Contro
atteries may
e wea
, rep
ace t
em wit
new ones
Leave the unit unplugged
or 20-30 min, plug the unit back in. I
the unit
does not power on please contact our customer service center
or service
on t
e mo
e
No
icture, sound or menu a
ears on
h
r
n
• Dependin
on the Source/Connection, confirm the followin
-For Antenna/Basic Ca
e
re
o an Auto Scan on t
e mo
e
-For Sate
ite Receiver/Ca
e Box, c
ec
t
e connections to ma
e sure
ey are secure
y connecte
-For RF Coaxial Cable
redo an Auto Scan on the model
-For RCA Au
io/Vi
eo, c
ec
t
e connections to ma
e sure t
e
are
ecure
connecte
• Check i
the connections are made securely and correctly
• Check if the cables are dama
ed
Check i
a correct external input channel is selected on
our TV. (Re
er to page 22.
• Check i
you have completed the channel setting. (Re
er to pages 29-31.
• While the setup menu or timer programming displa
is shown, or while the
screen saver is active
the audio is muted
Clock settin
and channel settin
cannot be
erformed
• If a recordin
is in pro
ress, these operations cannot be performed
Time jumps/Auto C
oc
set’s incorrect
t
me
• Set t
e “Auto C
oc
Setting” to “OFF” on page 104 an
try “Manua
C
oc
Setting
on page 34
T
e unit
oes not operate proper
y
Moisture
as con
ense
insi
e t
e unit. Remove t
e
isc an
eave t
e unit
turned on
or about 2 hours until the moisture evaporates. (Re
er to page 3.)
“Repairin
” appears on the TV screen
Repairing
• I
there is a power
ailure or unplugging during recording,
inalizing,
ormatting or editing (even a
ter “Repairing” disappears), a repairing
process will begin automaticall
just a
ter turning the unit on again
It may ta
e severa
minutes up to severa
ours
In case you inten
to cance
t
e
repa
r
ng process
Repairing
Do you want to cancel a repairing
process? When selecting “Yes”,
the disc may not be usable.
Yes
No
• I
you intend to cancel the repairing process, press
PEN
CL
SE
on the
ront panel, then select “Yes” and press
K
. A
ter that, press
PEN
CL
SE
to ta
e out t
e
isc.
e
isc cance
e
uring t
e
repairing process MAY NOT wor
T
e c
oc
isp
ay
oes not appear in
the
ront panel display
• C
ec
t
at t
e AC power cor
is connecte
secure
y
• (In case of power failure) Check the breaker and clock settin
hen
ou forget the password for
arental lock
• Please cancel the password and the set level. (Refer to pa
e 106.
No analo
TV closed captions are
ou
u
• If
ou are using HDMI connection to watch the TV programs through
this unit, analog TV closed caption cannot be output. Tr
using another
out
ut connection to the TV
Instructions continue on the next pa
e
