37
En
■ Speakers Type
`Normal
:
Select this if you’ve connected your front speakers
normally.
`Bi-Amp:
Select this if you’ve bi-amped your front speakers.
Note
• Powered Zone 2 cannot be used if “Speakers Type” setting is set
to “Bi-Amp” (➔ 50).
■ Speaker Terminal Assign
Front High/Zone2
With this setting, you can specify the speakers con-
nected to FRONT HIGH OR ZONE 2 SPEAKERS
terminals.
`Front High
:
Front high speakers can be used.
`Zone2:
Zone 2 speakers can be used (Powered Zone 2
enabled).
Note
•If the “Speakers Type” setting is set to “Bi-Amp”, Powered
Zone 2 cannot be used.
SurrBack/Front High
With this setting, you can specify the speakers con-
nected to SURR BACK OR FRONT HIGH SPEAK-
ERS terminals.
`Surr Back
:
Surround back speakers can be used.
`Front High:
Front high speakers can be used.
Note
•If the “Speakers Type” setting is set to “Bi-Amp”, Powered
Zone 2 cannot be used.
•If “Front High” is selected in the “Front High/Zone2” setting,
you cannot select “Front High” here.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies.
■ Subwoofer
`Ye s
:
Select if a subwoofer is connected.
`No:
Select if no subwoofer is connected.
■ Front
`Full Band
`40Hz to 100Hz
, 120Hz, 150Hz, 200Hz
Note
•If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■ Center
*1
, Surround
*1
`Full Band
`40Hz to 100Hz
, 120Hz, 150Hz, 200Hz
`None:
Select if no speaker is connected.
■ Front High
*1*2*4*5
, Surr Back
*2*3*4*6
`Full Band
`40Hz to 100Hz, 120Hz, 150Hz, 200Hz
`None
:
Select if no speaker is connected.
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3
If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
*4
If the “Speakers Type” setting is set to “Bi-Amp” (➔ 37), or
Powered Zone 2 is being used (➔ 50), this setting cannot be
selected.
*5
If you have selected other than “Front High” in the “Front
High/Zone2” or “SurrBack/Front High” setting, this setting
cannot be selected.
*6
If you have selected other than “Surr Back” in the “Surr-
Back/Front High” setting, this setting cannot be selected.
■ Surr Back Ch
`1ch:
Select if only one surround back speaker L is con-
nected.
`2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
• If the “Surr Back” Setting is set to “None” (➔ 48), this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
`80Hz, 90Hz, 100Hz, 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
■ Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
`On
:
Double Bass function on.
`Off:
Double Bass function off.
Note
• This function can be set only if the “Subwoofer” setting is set to
“Ye s”, and the “Front” setting is set to “Full Band”.
This setting is set automatically by Audyssey 2EQ
®
Room Correction and Speaker Setup function (➔ 22).
