Manual-3
REAR PANEL DESCRIPTION
1 Channel Input jacks: consist of eight pairs of unbalanced ¼" tip-sleeve jacks, used to connect any line-level signal source to the
SM 82S. As indicated, only the LEFT is to be used if the Input is mono and should therefore appear in both Left and Right chan-
nels, depending on the position of the front panel PAN control.
2 MAIN EXPAND INPUT: A ¼" TRS stereo Input jack may link two or more SM 82Ss together, or accept the output from
another mixer. is may also be used to sum any xed-level stereo signal into the Main Outputs, producing a ninth stereo Input
when added with 1. A stereo Tip-Ring-Sleeve cable must be used here. e Left input is on the Tip, Right is on the Ring and the
Sleeve is ground.
3 LOOP EXPAND INPUT: Another ¼" TRS stereo Input, expands the stereo Loop buses of two SM 82Ss so they share the same
eects loop. A stereo Tip-Ring-Sleeve cable must be used here. Connect the LEFT and RIGHT LOOP SENDS (4) of the rst
unit to the LOOP EXPAND INPUT of the second SM 82S. (Tip = left; Ring = right.)
4 LOOP SEND: is pair of ¼" jacks may drive an eect or similar device which is to be returned to item 5 below. If a mono
device is used, both the Left and Right Send channels of the SM 82S are summed together and presented at the LEFT Output if
nothing is inserted in the RIGHT Output.
5 LOOP RETURN: ese ¼" aux returns may connect the output of a reverb or other eect unit to the Loop bus of the SM 82S.
If no eect is used, they can be used as a tenth stereo Input to the mixer in addition to those described in 1 and 2. As with the
other stereo Inputs, mono signal may be connected to the LEFT input to obtain two-channel mono operation.
6 MAIN EXPAND OUTPUT: is ¼" TRS stereo (Tip = left, Ring = right) Output jack connects one SM 82S to another for the
purpose of expanding the number of Inputs available. Use only a stereo plug in this jack — a mono jack or cable will cause loss of
Right channel signal and possibly distortion to the Left channel. is Output also serves as a xed pre-fader level useful as record
outputs or other applications. You may use a send/return cable to drive a
7 Main BALANCED OUTPUT: ese balanced Tip-Ring-Sleeve jacks connect the main Outputs of the SM 82S to a power
amplier or to additional signal processing. As is the AES standard with all Rane balanced outputs using ¼" TRS jacks, the Tip is
(+), the Ring is (–) and the Sleeve is ground.
8 Power connector: e internal universal switching power supply operates on any AC mains 100 to 240 VAC, 50 or 60 Hz (most
places in the world). All that is required when traveling is the appropriate IEC line cord.
ALL INPUTS ARE UNBALANCED
TIP=L, RING=RTIP=L, RING=R
RANE CORP. MADE IN U.S.A.
87654321
LEFT
(MONO)
RIGHT
LEFT
(MONO)
RIGHT
OUTPUT
BALANCED
LOOP SEND
UNBALANCED
MAIN
EXPAND
INPUT
LOOP
EXPAND
INPUT
LEFT
(MONO)
RIGHT
LEFT
(MONO)
RIGHT
LEFT
(MONO)
RIGHT
LEFT
(MONO)
RIGHT
LEFT
(MONO)
RIGHT
LEFT
(MONO)
RIGHT
LEFT
RIGHT
RIGHTLEFT
(MONO)
ACN 001 345 482
LOOP RETURN
UNBALANCED
MAIN
EXPAND
OUTPUT
UNBALANCED
RIGHTLEFT
(MONO)
COMMERCIAL AUDIO
EQUIPMENT 24TJ
R
100-240 V
50/60 Hz 7 WATTS
SM 82S
1
2 378 6 5 4
