Filter
Top Products
2
IMPORTANT SAFETY RULES
WARNING: Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
WARNING: When using Electric Tools, basic safety precautions
should always be followed to reduce the risk of fire, electric shock, and
personal injury, including the following:
1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite
injuries.
2. CONSIDER WORK AREA ENVIRONMENT. Don’t expose power
tools to rain. Don’t use power tools in damp or wet locations. Keep
work area well lit.
3. KEEP CHILDREN AWAY. All visitors should be kept away from
work area. Do not let visitors contact tool or extension cord.
Supervise the use of this tool by children.
4. STORE IDLE TOOLS. When not in use, tools should be stored in
dry, high or locked-up place — out of reach of children.
5. USE SAFETY GLASSES.
6. DON’T ABUSE CORD. Never carry tool by cord or yank it to
disconnect from receptacle. Keep cord from heat, oil, and sharp
edges.
7. DON’T OVERREACH. Keep proper footing and balance at all
times.
8. DISCONNECT TOOLS. When not in use, before servicing and
when changing accessories.
9. This tool is recommended for indoor use only
10. STAY ALERT. Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
11. DO NOT TOUCH THE HEATED TIP OF THE TOOL OR THE HOT
MELTED SOLDER. The operating temperature of this tool is
approximately 900°F on the HIGH (II) setting and 500° on the LOW
(I) setting.
12. Never attempt to use any material other than that recommended in
this manual.
13. Keep your craft iron well away from all flammable material.
14. To avoid burns, always assume that the tip is hot and return the
craft iron to its protective stand.
15. Never leave your tool plugged in and unattended. After use, unplug
tool, allow the tip to cool and store in a safe place.
16. Before making any adjustment (removing or replacing a tip, etc.)
make sure the tool is unplugged and cool.
17. Always work in a well ventilated area.
18. Do not dip the tool into a liquid.
WARNING: This product contains chemicals, including lead, known to
the state of California to cause cancer, and birth defects or other
reproductive harm.
Wash hands after handling. This also applies to
lead based solders.
Extension Cords
An extension cord must have adequate wire size (AWG or American Wire
Gauge) for safety, and to prevent loss of performance. The smaller the
gauge number of the wire, the greater the capacity of the cable; that is, 16
gauge has more capacity than 18 gauge. When using more than one
extension cord to make up the total length, be sure each individual
extension contains at least the minimum wire size. Before using an
extension cord, inspect it for loose or exposed wires, damaged insulation
and defective fittings. Make any needed repairs or replace the cord if
necessary. To determine the minimum size required, refer to the chart
below:
Polarized Plug
This appliance has a polarized plug (one blade is wider than the
other ). To reduce the risk of electric shock, this plug is intended to fit
into a polarized outlet only one way. If the plug does not fit fully into
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not modify the plug in any way.
SAVE THESE SAFETY RULES FOR FUTURE USE
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more American Wire Gage
Than Than
0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
632901-00 Iron 10/24/05 12:37 PM Page 2