Black & Decker FS540 Cordless Sander User Manual


  Open as PDF
of 20
 
5
Personal Safety
•Nochildrenorpregnantwomenshouldentertheworkareawherethepaintsandingis
being done until all clean up is completed.
•Adustmaskorrespiratorshouldbewornbyallpersonsenteringtheworkarea.Thefilter
should be replaced daily or whenever the wearer has difficulty breathing.
NOTE: Only those dust masks suitable for working with lead paint dust and fumes
should be used. Ordinary painting masks do not offer this protection. See your local
hardwaredealerfortheproper(NIOSHapproved)mask.
•NOEATING,DRINKINGorSMOKINGshouldbedoneintheworkareatoprevent
ingesting contaminated paint particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the
work area where dust would settle on them.
Environmental Safety
•Paintshouldberemovedinsuchamannerastominimizetheamountofdustgenerated.
•Areaswherepaintremovalisoccurringshouldbesealedwithplasticsheetingof4mils
thickness.
•Sandingshouldbedoneinamannertoreducetrackingofpaintdustoutsidetheworkarea.
Cleaning and Disposal
•Allsurfacesintheworkareashouldbevacuumedandthoroughlycleaneddailyforthe
duration of the sanding project. Vacuum filter bags should be changed frequently.
•Plasticdropclothsshouldbegatheredupanddisposedofalongwithanydustchipsor
other removal debris. They should be placed in sealed refuse receptacles and disposed
of through regular trash pick-up procedures. During clean up, children and pregnant
women should be kept away from the immediate work area.
•Alltoys,washablefurnitureandutensilsusedbychildrenshouldbewashedthoroughly
before being used again.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means
your tool will operate on standard 60 Hz household power. Do not operate AC tools on
DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC
or DC power. This information is printed on the nameplate. Lower voltage will cause loss
of power and can result in over-heating. All Black & Decker tools are factory-tested; if this
tool does not operate, check the power supply.
Assembly/Adjustment Set-Up
WARNING: Always unplug sander from power supply before any of the following
operations.
Attaching Sandpaper
To operate the paper clamps on your sander, simply lift them up with your thumb, as shown
in Figure 1. Rotate the clamp lever downward until the clamp is fully opened.
Insert one short edge of the paper under the clamp. Push edge squarely up against the flat
wall of the platen and close the paper clamp on that side. Wrap the sandpaper around to
fit the other edge under the opposite paper clamp. Push as much paper under the second
clamp as possible before securing the paper clamp. Any slack in the paper will reduce
sanding performance.
NOTE: The FS540 comes with the paper punch shown in figure 2. The punch may be
permanently attached to a workbench by screwing it down using the two holes provided.
Ifitisonaworksurfacesimplypressthesander(withsandpaperfirmlyattached)down
on the punch to create the dust collection holes. If it is hand held simply press the punch
against the sander pad.
Operating Instructions
WARNING: To reduce the risk of serious personal injury, read, understand and follow
all important safety warnings and instructions prior to using this tool.
Switch
To turn the tool ON, push the portion of the dust protected switch marked “I”. To turn the
tool OFF, push the portion of the switch marked “O”.
Operation
Grasp the sander and turn it ON. Move it in long, sweeping strokes along the surface,
letting it do the work. Utilize an even pressure across the sanding pad. Excessive pressure
 previous next