A SERVICE OF

logo

Open as PDF
next previous
7
OPERATING INSTRUCTIONS
•Donotusescrewdriverasaprybarinany
position.
•Toavoidscrewdriverbeingturnedon
accidentally, do not carry in your pocket.
OPERATING IN POWER MODE
Forward
•Rotatethecollar(4)tothepositionmarked
as shown in figure F.
•Slidetheforward/reverseswitch(1)tothe
right, exposing the arrow pointing forward
as shown in figure F.
•Pressthebuttonontheswitchandthetoolwill
run; release the button and the tool will stop.
Reverse
•Rotatethecollar(4)tothepositionmarked
as shown in figure F1.
•Slidetheforward/reverseswitch(1)tothe
left, exposing the arrow pointing backward.
•Pressthebuttonontheswitchandthetoolwill
run; release the button and the tool will stop.
FORWARD/REVERSE/LOCK-OFF SLIDER
•Whentheforward/reverseslider(1)isinthe
central position the tool is locked off to prevent
accidental actuation or battery discharge.
OPERATING IN MANUAL MODE
•Rotatethecollartothepositionmarked
as shown in figure G.
•Usethetoolasanyconventionalnon-
powered screwdriver. When the forward /
reverse slider (1) is in the central position
the tool is locked off to prevent accidental
actuation or battery discharge.
NOTE: If the collar fails to move past the
cental lock position to manual mode then
please see the following procedure:
1. Turn clutch collar to Power Mode .
(figure G1)
2. Run the unit.
4. Turn clutch collar to Manual Mode .
(figure G1)
SCREW DRIVING
•Beforeinstallingbits,movetheforward/reverse
slider(1)tothecenter“lock-off”position.
•Inserttheappropriatehexshank
screwdriver bit into the spindle.
•Selectforwardorreverserotation.
DRILLING
•Beforeinstallingbits,movetheforward/reverse
slider(1)tothecenter“lock-off”position.
•Inserttheappropriatehexshankdrillbit.
•Selectforwardrotation.
NOTE: When drilling, the bit may become
disconnected from the spindle upon
withdrawing it from the material. Should
this occur, the bit can be removed by
re-insertingthehexshankintothespindle
and running the tool in the reverse direction.
GENERAL DRILLING TIPS
•Thistoolisnotrecommendedfordrilling
in masonry.
•Usesharpdrillbitsonly.
•Drillbitsformetalcanbeusedfordrilling
holes in wood. These bits must be sharp
and should be pulled out frequently when
drilling to clear chips from the flutes.
•Supportandsecureworkproperly,as
instructed in the safety Instructions.
•Useappropriateandrequiredsafety
equipment, as instructed in the safety
instructions.
•Secureandmaintainworkarea,as
instructed in the safety instructions.
•Applypressureinastraightlinewiththe
bit. Use enough pressure to keep the
bit biting but not so much as to stall the
motor or deflect the bit.
•Holdthetoolfirmlytocontrolitstwistingaction.
•DONOTCLICKTHETRIGGEROFA
STALLED TOOL OFF AND ON IN AN
ATTEMPT TO START IT. DAMAGE TO
THE TOOL CAN RESULT.
•Minimizestallingonbreakthroughby
reducing pressure and slowly drilling
through last part of hole.
•Keepthemotorrunningwhilepullingthebitout
of a drilled hole. This will help reduce jamming.
•Makesureswitchturnstoolonandoff.
WARNING: It is important to support
work properly and to hold the tool firmly to
prevent loss of control which could cause
personal injury.
MAINTENANCE
Use only mild soap and damp cloth to
clean the tool. Never let any liquid get
inside the tool; never immerse any part of
the tool into a liquid.
IMPORTANT: To assure product SAFETY
and RELIABILITY, repairs, maintenance
and adjustment (other than those listed
in this manual) should be performed by
authorized service centers or other qualified
service personnel, always using identical
replacement parts.
Thisproductuseslithium-ionrechargeable
and recyclable batteries. When the batteries
no longer hold a charge, they should be
removed from the product and recycled.
They must not be incinerated or composited.
The batteries can be taken for disposal
toaBlack&Decker,Company-Owned
or Authorized Service Center. Some
local retailers are also participating in a
national recycling program (see “RBRC™
BATTERY REMOVAL AND DISPOSAL