Filter
Top Products
-2-
*&)&3):3)*789&3)&11
.3897:(9.438 Failure to
follow all instructions listed below and in your
miter saw manual may result in serious
personal injury.
:11> &88*2'1* &3) 9.,-9*3 &11 9-*
+&89*3*787*6:.7*)+479-.889&3)184
7*2*2'*7944((&8.43&11>(-*(09-*
89&3)&3)2&0*8:7*.9.889.119.,-9A
loose stand is unstable and may shift in use
and cause serious injury.
":7394418<.9(-4++&3)).8(433*(954<*7
'*+47*24:39.3,949-*89&3) Unintended
startup during assembly can cause injury.
*+47*45*7&9.3,2&0*8:7*9-**39.7*
:3.9 .8 51&(*) 43 & 841.) +1&9 1*;*1
8:7+&(* Serious injury could occur if tool
with stand is unstable and tips.
*;*789&3)43944147.9889&3)47:8*&8
1&))*7478(&++41).3, Serious injury could
occur if the tool is tipped or the cutting tool is
accidentally contacted. Do not store
materials on or near the tool such that it is
necessary to stand on the tool or its stand to
reach them.
#8*431>48(-7*51&(*2*395&798 Any
others may create a hazard.
The Miter Saw should be firmly mounted to
the stand per the instruction manual.
After mounting the Miter Saw to the stand,
align, position and balance the Miter Saw per
the instruction manual.
Before use, verify that all stand parts are free
from damage and/or deformity.
Before use, verify that all parts or
components of the stand are properly
installed.
When mounting the Miter Saw to the stand,
make sure that the tool mount handles are in
the “UNLOCK” position, so the tool mount will
engage with the main rail. Be sure to hold the
saw until it is secured to prevent it from
falling off the main rail. Handles should then
be locked. (See page 10 for detailed
instructions.)
When removing the Miter Saw from the
stand, pull the tool mount handles until they
rotate to the “UNLOCK” position. Hold the
Miter Saw firmly to prevent the saw from
falling off the main rail. Carefully remove the
Miter Saw. (See page 10 for detailed
instructions.)
Do not modify the stand in any manner or
use the stand for any purpose other than is
stated in these instructions.
Because cut material may cause the stand to
become unbalanced, always be sure the
material is supported properly. Also, if the
piece being cut is placed far beyond the work
support, the opposite side may suddenly be
lifted up due to weight imbalance. To prevent
this from occurring, hold the opposite side
firmly before cutting.
!
WARNING
!&+*9>3897:(9.438+47".9*7!&<!9&3)
"-.8"7&;.9> .8*.9*7!&<!9&3).8)*8.,3*)94'*:8*)
<.9-9-*+4114<.3,2.9*78&<8
Other units may be compatible, but have not been verified for use with the T4B system.
48(-
4212, 4212L, 4410, 4410L,
4412, 4405, 5412L, 3912,
3915, 3918, 3924
*19&
36-255, 36-255L, 36-240,
MS450
*$&19
DW712, DW705S, DW703,
DW708, DW706, DW718,
DW715, DW716, DW709
&0.9&
LS1214, LS1221, LS1013,
LS1212, MS1214F
.1<&:0**
6497-6
.),.)
MS1065LZ, MS1250LZ
>4'.
TS1353DXL, TS1341, TS1552