DeWalt DW621 Router User Manual


 
ENGLISH
en - 4 19
The cable wire colours, or a letter, will be marked
at the connection points of most good quality
plugs. Attach the wires to their respective points
in the plug (see below). Brown is for Live (L) (2)
and Blue is for Neutral (N) (4).
Before replacing the top cover of the mains plug
ensure that the cable restraint (3) is holding the
outer sheath of the cable firmly and that the two
leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N)
wires to the earth pin marked E or .
For 115 V units with a power rating exceeding 1500 W,
we recommend to fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
size is 1.5 mm
2
. When using a cable reel, always
unwind the cable completely. Also refer to the table
below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.066 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing a cutter (fig. B)
Press and hold down the spindle lock (2).
Using the 17 mm wrench, loosen the collet nut
(3) a few turns and insert a cutter.
Tighten the collet nut and release the spindle lock.
Never tighten the collet nut without a
cutter in the collet.
Replacing the collet assembly (fig. C)
Your router is supplied with a 8 mm (GB: 1/4") collet
fitted to the tool. Two other precision collets are also
available to suit the cutter used. The collet and the
collet nut are inseparable.
Loosen the collet nut (3) completely.
Remove the collet assembly (21).
Fit a new assembly and tighten the collet nut (3).
DW621 -
Setting the electronic speed control dial (fig. A)
The speed is infinitely variable from 8,000 to
24,000 min
-1
using the electronic speed control dial
(19) for uniform cutting results in all types of wood,
plastics and in aluminium.
Turn the electronic speed control dial to the
required level.
Generally, use the low setting for large diameter
cutters and the high setting for small diameter
cutters. The correct setting, however, is a matter of
experience.
1 = 8,000 min
-1
2 = 9,500 min
-1
3 = 11,500 min
-1
4 = 16,000 min
-1
5 = 19,500 min
-1
6 = 22,500 min
-1
7 = 24,000 min
-1