Filter
Top Products
For Your Safety...
When using electric tools, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock, and personal injury, including the following:
READ AND SAVE ALL THE FOLLOWING INSTRUCTIONS:
1. Keep work area clean -- Cluttered areas
and benches invite injuries.
2. Avoid dangerous environment -- Don't
expose tools to rain. Don't use power tools in
damporwetlocations. Don't use power tools
in the presence of flammable liquids or gases.
Avoid chemical or corrosive environments
Keep work area welt lit.
3. Guard against electric shock -- Prevent
body contact with grounded surfaces. For
example: pipes, radiators, refrigerator
enclosures.
4. Keep children away -- Do not let visitors
contact tool or extension cord. All visitors
should be kept away from work areas.
5o Store idle tools -- When not in use, tools
should be stored in dry, and high or locked-
up place - out of reach of children.
6. Don't force t,:ol -- It will do the job better
and safer at the rate for which it was intended.
7. Use right tool - Don't force small tool or
attachment to do the job of a heavy-duty tool.
Don't use tool for purpose not intended - for
example - don't use circular saw for cutting
tree limbs or logs.
8, Dress properly _ Do not wear loose cloth-
ing or jewetry. They can becaught in moving
parts. Rubber gloves and non-skid footwear
are recommended when worR.ing out-
doors. Wear protective hair coyering to con-
tain long hair.
9. Use safety glasses -- Also use face or dust
mask if cutting operation is dusty.
10. Don't abuse cord -- Never carry tool by
cord or yank it to disconnect from recep-
tacle. Keep cord from t_eat, oil, and sharp
edges.
11. Secure work -- Use clamps or vise to
hold work. It's safer than using your hand and
it frees both hands to operate tool.
12. Don't over-reach _ Keep proper footing
and balance at all times,
13. Maintain tools with care -- Keep tools
sharp and clean for be_er and safer perfor-
mance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and if damaged, have repaired,
by authorized service facility. Inspect exten-
sion cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil
and grease.
14. Disconnect tools -- Wh en not in use, before
servicing, and when ohanging accessories,
such as blades, bit, cutters.
15. Remove adjusting keys and wrenches--
Form habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it on.
16. Avoid unintentional starting -- Don't
carry plugged-in tool with finger on switch.
Be sure switch is off when plugged in.
17. Outdoor use extension cords -- When
tool is used outdoors, use only extension
cords intended for use outdoors and so
marked.
18. Stay alert -- Watch what you are doing.
Use common sense. Do not operate tool
when you are tired. Don't use power tools
after taking drugs, alcohol or medications.
19, Do not alter or misuse tool -- These tools
are precision built. Any alteration or mod-
ification not specified is misuse and may
result in a dangerous condition.
20. Avoid gaseous areas -- Do not operate
portable electric tools ingaseous or explosive
atmospheres, Motors in these tools normally
spark, and the sparks might ignite fumes.
21 Check for damaged parts-- before further
use of the toot, check for damaged parts.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mount-
ing, and any other conditions that may affect
its operation. A part that is damaged should
be properly repaired or replaced by authorized
service center before further use of the tool.
Have defective switches replaced by authorized
service center. Do not use tool if switch does
not turn it on and off.
22. Your tool is double insulated -- And no
grounding is necessary. The tool is equipped
with atwo wire cord and two prong plug which
can be used instandard 120 volt A.C° curriers.
Use only identical replacement part= when
service is required.
23. EXTENSION CORDS - An undersize
cord will cause a drop in line voltage, result-
ing in toss of power and over-heating. Use 18
gauge or heavier cord. NOTE: The smaller
the gauge number, the heavier the cord.
(Extension cords are available.)
24. WARNING: Use of damaged cords can
shock, burn or electrocute.
READ AND SAVE ALL THE PRECEDING INSTRUCTIONS
Dremel Limited Warranty
Your Dremet product is warranted against defective material or
workmanship for a period of one year from date of purchase. In
the event of a failure of a product to conform to this written
warranty you should return the product, along with proof of
purchase date and a written statement about the nature of the
problem, to:
Dremel Service Center
4915 Twenty-first Street
Racine, Wisconsin 53406
or
Oreme! Service Center
4631 E. Sunny Dunes
Palm Spring, California 92264
No employee, agent, dealer or other person is authorized to give
any warranties on behalf ofDremel. IfOremelinsoeclionshows
that the problem was caused by defective material or work-
manship within the limitations of the warranty, Dremel will repair
or replace the product free of charge and return product pre-
paid. Repairs made necessary by normal wear or abuse, or
repair for product outside the warranty period, if they can be
made, will be charged at regular factory prices.
OREMEL MAKES NO OTHER WARRANTY OF ANY KIND
WHATEVER, EXPRESSED OR IMPLIED, AND ALL IMPLIED
WARRANTIES OF MERCHANTASILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH EXCEED THE ABOVE
MENTIONED OBLIGATION ARE HEREBY DISCLAIMED BY
DREMEL AND EXCLUDED FROM THIS LIMITED WARRANTY.
This warranty gives you specific legal rights and you may also
have Diner rights which vary from state to state. The obligation of
the warrantor is soley to repair or replace the product. The
warrantor is not liable for any incidental or consequential
damages due to such defect. Some states do not allow the exclu-
sion or limitations of incidental or consequential damages, so the
above limitations or exclusion may not apply to you.
For prices and warranty fulfillment in Ihe continental United States,
contact your local Dremel distributor,
Page 2