Filter
Top Products
&'+"#%'!!&'%('"!&
'!&#'"!
#9A0<=?::6C 230V~ 50Hz
,B9?>:?> 2000 Watts
'07:,>9?>60> Position 350°C
Position 600°C
*0423>
0B.6 89DD60= 750g
"(''
The HG2000 is a highly versatile electric
heat gun which can be used for many
different applications, such as:
●
Removal of paint
●
Defrosting metal water pipes
●
Forming and welding plastic
●
Heat shrinking tubing
●
Soldering
'""'!'&'%&('&%"
+"(%'(!#&%'
!&'%('"!&%(+"%
(&
'&''!&
The heat gun has two settings:
1. Low heat (switch down) - for use
where the work surface or
surroundings must not be allowed to
get too hot.
Setting~350°C.
2. High heat (switch up) - for faster heat
up time of the work surface where
you can also operate the gun at a
greater distance.
Setting~600°C.
2
!
PLEASE READ BEFORE USE
DO NOT
●
Touch the nozzle.
●
Change/rotate the nozzle while the unit is
turned on.
●
Leave the heat gun unattended when it is
switched on.
●
Allow children to operate or play with the
heat gun.
●
Carry the heat gun by the mains cable.
●
Allow heat to be directed onto the mains
cable.
●
Use the heat gun as a hair dryer.
●
Restrict air flow from the nozzle outlet or
fan inlets.
●
Allow the heat gun to become damp or be
operated in damp conditions.
●
Use the heat gun close to inflammable
materials because heat may be conducted
to combustible materials which are out of
sight.
●
Apply to the same place for a long time.
●
Under any circumstances aim the heat gun
at another person or animal.
●
Do not use when explosive vapour or dust
is in the air.
,820<91-?<8=*0<0.97708/
A0,<482,:,4<9130,@C2<,/0898
#)>C:0A9<5269@0=,820<9114<0
9<0B:69=49841>30,::64,8.04=89>
?=0/A4>3.,<0
●
When changing the nozzle, switch off and
allow the accessory and nozzle to cool.
●
After use stand the heat gun up vertically
(on its rear end) and allow to completely
cool down.
●
A hot nozzle can cause damage.
●
Before every use check the condition of
the plug and cable. If these are damaged in
any way do not use. Repairs must be
carried out by a fully qualified electrician.
●
Always ensure there is adequate
ventilation as gases and vapours may be
given off when stripping paint. Ensure that
protective goggles and masks are used.
●
Poisonous or inflammable gases may be
produced when working with paints
(especially older type lead paints),
varnishes, plastics and similar materials.
●
Ensure the heat gun switch is in the off
position when connecting to the mains.
●
Ensure children and pets are kept away
from the work area.
●
It is recommended a RCD (residual
current device) rated at 30mA is fitted
into the mains socket-outlet first for added
protection against electric shock.
●
This product is intended for ‘household’
use only.
●
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
Thermal cut out – This heat gun is fitted with a self resettable thermal cut-out. If you find the
fan is on but the heating element is off, hold the gun away from the work piece and allow the
fan to cool the element. The heat gun should reset in approx. 1min.