Festool DX 93 E Sander User Manual


 
5
dust extraction. Order numbers can be found in
the corresponding brochures.
The Stickfi x abrasives are simply pressed onto the
Stickfi x sanding pad and pulled off after use.
If the front tip of the abrasive has become worn
it can be removed from the sanding pad, rotated
around 120° and replaced.
Systainer
Many Festool products are shipped in a unique
system container, called "Systainer". This provides
protection and storage for the tool and acces-
sories. The Systainers are stackable and can be
interlocked together. They also can be interlocked
atop Festool CT dust extractors.
4.3
4.2
4.1
- Place one systainer on top of the other.
- Release all four latches on the lower systainer
by pulling back at their top edges (4.1).
- Slide all four latches upward (4.2).
- Snap all four latches back to their fl at position
(4.3) so they engage the stacking tabs of the
upper systainer.
Maintenance and care
Always disconnect the machine at
its mains plug before performing maintenance
work!
Any maintenance and repair work re-
quiring the motor casing to be opened may only be
carried out by an authorised service workshop.
The vent openings on the motor casing must
always be kept clean and free to ensure a good
circulation of air.
The device is fi tted with self-disconnecting special
brushes. If these become worn the power is au-
tomatically interrupted and the device comes to
a standstill. Any maintenance and repair work re-
quiring the motor casing to be opened may only be
carried out by an authorised service workshop.
Accessories, tools
For safety reasons, only use original
Festool accessories and tools!
The accessory and tool order number can be
found in the Festool catalog or on the Internet
under www.festool-usa.com.
Warranty
Conditions of 1+2 Warranty
You are entitled to a free extended warranty (1
year + 2 years = 3 years) for your Festool power
tool. Festool shall be responsible for all shipping
costs during the fi rst year of the warranty. Dur-
ing the second and third year of the warranty the
customer is responsible for shipping the tool to
Festool. Festool will pay for return shipping to the
customer using UPS Ground Service. All warranty
service is valid 3 years from the date of purchase
on your receipt or invoice.
Festool Limited Warranty
This warranty is valid only on condition that the
tool is used and operated in compliance with the
Festool operating instructions. Festool warrants,
only to the original consumer purchaser, that the
specifi ed tool will be free from defects in materi-
als and workmanship for a term of one year from
the date of procurement. Festool makes no other
warranty, express or implied, for Festool portable
power tools. No agent, representative, distributor,
dealer or employee of Festool has the authority
to increase or otherwise change the obligations
or limitations of this warranty. The obligations of
Festool in its sole discretion under this warranty
shall be limited to the repair or replacement of
any Festool portable power tool that is found to be
defective as packaged with the User Manual.
Excluded from coverage under this warranty are:
normal wear and tear; damages caused by mis-
use, abuse or neglect; damage caused by anything
other than defects in material and workmanship.
This warranty does not apply to accessory items
such as circular saw blades, drill bits, router bits,
jigsaw blades, sanding belts, and grinding wheels.
Also excluded are “wearing parts”, such as carbon
brushes, vanes of air tools, rubber collars and
seals, sanding discs and pads, and batteries.
Festool portable power tools requiring replace-
ment or repair are to be returned with the receipt
of purchase to Festool (call 800-554-8741 for
address details).
IN NO EVENT SHALL FESTOOL BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDEN-
TAL DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED WHATSOEVER. ALL WARRANTIES