Grizzly G0516 Lathe User Manual


  Open as PDF
of 64
 
"&-"
BdYZa<%*&+B[\#-$%+ 
4. EaVXZVe^ZXZd[eanlddYdkZgi]ZWZY"lVnh
idegdiZXindjg]VcYh#
ALWAYS place a piece
of plywood over lathe
bed-ways before remov-
ing or installing a lathe
chuck. This covers the
sharp corners of the
bed, protecting your
hands and fingers from
a pinch injury.
Figure 15.He^cYaZcdhZXdbedcZcih#
AdX`EaViZ
Bdjci^c\
Cjih
Figure 16.GZbdk^c\aVi]ZX]jX`#
5. =daYi]ZX]jX`$[VXZeaViZl^i]ndjg]VcYdgV
X]jX``Zn!VcYjh^c\V&,bblgZcX]!addhZc
i]Z(X]jX`bdjci^c\cjihdci]ZWVX`d[i]Z
`cjgaZY adX` eaViZ# 9D CDI WVX` i]Z cjih
djiVaai]ZlVndgi]Znl^aahXgViX]i]ZbZiVa
XdkZgl]ZcndjgdiViZi]ZaVi]ZX]jX`#
6. GdiViZi]Z`cjgaZYadX`eaViZidlVgYi]Z[gdci
d[i]ZaVi]Z#
7. GZbdkZi]ZX]jX`$[VXZeaViZ[gdbi]Zhe^cYaZ
cdhZWnejaa^c\^idjiFigure 16#Note-—the
tolerances are tight, so you may need to wig-
gle the chuck/faceplate back-and-forth, rotate
it
1
⁄4 of a turn, wiggle it, rotate it and continue
repeating this process until the chuck comes
out. Never use a pry bar or other similar tool
to force the chuck/faceplate out!
Removing Chuck
or Faceplate
I]ZBdYZa<%*&+he^cYaZcdhZbdjci^c\hnhiZb
jhZh VX^gXjaVg adX` eaViZl^i] hadiiZY]daZh i]Vi
VgZ dkZgh^oZY Vi dcZ ZcY `Zn]daZh# L]Zc i]Z
adX` eaViZ ^h gdiViZY XdjciZgXadX`l^hZ Vh [VX"
^c\i]ZX]jX`!i]ZX]jX`dg[VXZeaViZhijYhl^i]
bdjci^c\cjihXVceVhhi]gdj\]i]Zhe^cYaZcdhZ#
L]Zci]ZadX`eaViZ^hgdiViZYidlVgYi]ZWVX`d[
i]ZaVi]Z!i]ZdkZgh^oZY]daZhcVggdlidi]Zh^oZ
d[ i]Z hijYh! Vaadl^c\ i]Z bdjci^c\ cjih id WZ
i^\]iZcZYV\V^chii]ZWVX`d[i]ZadX`eaViZ!i]jh!
hZXjg^c\i]ZX]jX`dg[VXZeaViZ#
To remove a chuck or faceplate from the lathe
spindle nose:
1. Disconnect the lathe/mill from the power
source!
2. BdkZi]ZaVi]ZZnZh]^ZaYWVX`VcYdjid[i]Z
lVnd[i]ZaVi]ZX]jX`hdndj]VkZVXXZhh#
3. ;Vb^a^Vg^oZ ndjghZa[ l^i] i]Z he^cYaZ cdhZ
XdbedcZcihh]dlc^cFigure 15#
 previous next