Filter
Top Products
<%*&.B^aa$9g^aa$IVee^c\BVX]^cZ
"'*"
To mill a workpiece:
1# GZ[Zg id Basic Controls dc Page 16! VcY
aZVgci]Z]dlidjhZi]ZbVX]^cZXdcigdah#
2# 8aVbei]Zldg`e^ZXZidi]Zb^aa^c\iVWaZ!VcY
VY_jhi i]Z ]ZVYhidX` id i]Z cZZYZY ]Z^\]i!
YZei]d[Xji!VcYb^aa^c\eVi]#
Tip: Milling with the spindle fully extended,
can cause tool chatter. For maximum spindle
rigidity, keep the spindle retracted into the
headstock as far as possible with the spindle
lock lever locked and the fine feed lock knob
tightened.
3# GZ[Zg id Calculating and Setting Spindle
RPM dc Page 22 id [^cY i]Z WZhi he^cYaZ
GEBVcYhZii]Zhe^cYaZheZZY#
4. H]^[ii]Zhe^cYaZheZZYaZkZghidi]Zhe^cYaZ
heZZY [dg i]Z Veegdeg^ViZ b^aa^c\ heZZY [dg
i]ZY^VbZiZgd[XjiiZgVcYineZd[bViZg^Vaid
WZXji#
5# Eji dc ndjg hV[Zin \aVhhZh! ijgc i]Z bdYZ
hl^iX]id9G>AA>C<VcYegZhhHI6GI#
6# JhZ i]Z M"Vm^h dg N"Vm^h ]VcYl]ZZah id
hadlan [ZZYi]Z ldg`e^ZXZ ^cidi]Z XjiiZg# >[
ndjVgZdcanb^aa^c\^cdcZY^gZXi^dc!adX`i]Z
jcjhZYiVWaZha^YZ^ceaVXZ#
Milling /Drilling Mode Tapping Mode
Failure to follow RPM and feed rate
guidelines may endanger operator safety
from ejected parts or broken tools.
9ZeZcY^c\ dc i]Z [ZZY gViZ! idda ineZ! he^cYaZ
heZZY!VcYi]Zldg`e^ZXZbViZg^Vai]^hb^aa$Yg^aa$
iVee^c\bVX]^cZ]VhVbVm^bjbb^aa^c\Y^VbZiZg
d[(VcYbVm^bjbYg^aa^c\Y^VbZiZgd[&
*
¿-#I]Z
b^aa^c\iVWaZ]VhVXddaVciigdj\]l^i]VYgV^c[dg
Vcdei^dcVaXjii^c\[aj^YhnhiZb#
To drill and thread a hole:
1# GZ[Zg id Basic Controls dc Page 16, VcY
aZVgci]Z]dlidjhZi]ZbVX]^cZXdcigdah#
2# 8aVbei]Zldg`e^ZXZidi]Zb^aa^c\iVWaZ!VcY
VY_jhii]Z]ZVYhidX`idi]ZcZZYZY]Z^\]i[dg
Yg^aa^c\VcYiVee^c\#
3# HZii]ZYZei]hideVcYYg^aandjg]daZl^i]i]Z
Veegdeg^ViZheZZYVcYYg^aaW^ih^oZ[dgi]ZiVe#
Hidei]ZbVX]^cZl]ZcYdcZ#
4# HZii]Zhe^cYaZheZZYid&'%GEB!VcYgZVY"
_jhii]Z YZei]hide!hd Vii]ZWdiidb d[i]Z
he^cYaZhigd`Zi]ZYZei]hidel^aagZkZghZi]Z
he^cYaZWZ[dgZWdiidb^c\"djii]ZiVe#
5# Eji dc ndjg hV[Zin \aVhhZh! ^chiVaa i]Z iVe!
VcYijgci]ZbdYZhl^iX]idI6EE>C<#
6# 6eeaniVee^c\[aj^Y^[cZZYZY!egZhhHI6GI!
VcYWZ\^ci]gZVY^c\#
Tip:If the spindle return spring has too much
tension and fights the ability of the tap to
draw the spindle down, you can reduce the
return spring tension (refer to Page 18).
Failure to follow RPM and feed rate
guidelines may threaten operator safety
from ejected parts or broken tools.
Jh^c\ i]^h bVX]^cZ ^c i]Z iVee^c\ bdYZ iV`Zh
hdbZ aZkZa d[ h`^aa! hd bV`Z hjgZ id egVXi^XZ
jh^c\i]^h[ZVijgZ#L]Zc^ci]ZiVee^c\bdYZ!i]^h
bVX]^cZ^hYZh^\cZYidjhZiVehjeid
&
¿'Y^Vb"
ZiZg VcY id gZkZghZ he^cYaZ Y^gZXi^dc l]Zc i]Z
he^cYaZgZVX]Zhi]ZWdiidbd[^ihhigd`Z#>[Xjii^c\
i]gZVYh^cWa^cY]daZh!eVnheZX^VaViiZci^dcl]Zc
hZii^c\ i]Z bVm^bjb iVee^c\ YZei]# >[ i]Z iVe
gZVX]Zhi]ZWdiidbd[i]Z]daZWZ[dgZi]ZYZei]
hXVaZgZkZghZhhe^cYaZY^gZXi^dc!i]ZiVel^aah]ZVg
d[[^ci]Z]daZ#