Filter
Top Products
<),.&&'m(.AVg\Z8dbWdAVi]Z$B^aa
")*"
A. I]Z ild [ZZY gViZh·%#%%* >EG VcY %#%&%
>EG·VgZ[dgedlZgZYXVgg^V\ZigVkZa^ccdc"
i]gZVY^c\deZgVi^dch#
B. Ed^cii]Z Vggdld[ i]Z[ZZY gViZgVc\Z aZkZg
idi]Z1/LOadlgVc\Zedh^i^dcl]Zcjh^c\
[ZZY gViZh dg i]gZVY hZii^c\h ^c i]^h Xdajbc
hZZFigure 59#
NOTICE
Attempting to move the feed rate range
lever when the lathe is running will damage
the internal gears of the power feed mecha-
nism and will void the warranty. NEVER
attempt to move the feed rate range lever
when the lathe is running.
C. Ed^cii]Z Vggdld[ i]Z[ZZY gViZgVc\Z aZkZg
idi]Z2/HI]^\]gVc\Zedh^i^dcl]Zcjh^c\
[ZZYgViZhdgi]gZVYhZii^c\h^ci]^hXdajbc#
D. I]^h Xdajbc XdciV^chi]Z X]Vc\Z \ZVg Xdc"
[^\jgVi^dch[dgi]ZhZaZXiZY[ZZYgViZdgi]gZVY
hZii^c\#
E. I]^h hZXi^dc h]dlh i]Z X]Vc\Z \ZVg VcY
gVc\ZaZkZgXdc[^\jgVi^dc[dgmetrici]gZVYh#
F. I]^hhZXi^dch]dlh^aajhigVi^dchd[i]ZX]Vc\Z
\ZVghVcYi]Z^ggZaVi^dch]^ehiddcZVcdi]Zg#
G. I]^h hZXi^dc h]dlh i]Z X]Vc\Z \ZVg VcY
gVc\ZaZkZgXdc[^\jgVi^dc[dginchi]gZVYh#
Feed Rate Change Lever
I]Z[ZZYgViZX]Vc\ZaZkZgh]^[ihi]Z[ZZYgViZ
WZilZZc i]Z]^\]2/HI VcY adl 1/LO gVc\Zh!
VcYl^aa `ZZe i]ZaZVYhXgZl[gdb gdiVi^c\Yjg^c\
deZgVi^dcl]Zc ^c i]Z XZciZg cZjigVa 0/Nedh^"
i^dchZZFigure 59#
Ijgci]ZaVi]ZOFFVcYVaadli]Zhe^cYaZidXdbZ
idVXdbeaZiZhideWZ[dgZh]^[i^c\i]ZgVc\ZaZkZg#
>[ cZXZhhVgn id bZh] i]Z \ZVgh l]^aZ h]^[i^c\!
gdiViZi]Zhe^cYaZWn]VcYl^i]ha^\]iegZhhjgZdc
i]ZaZkZg#
Note: The illustrations provided at the top of the
B and C columns of the feed rate configuration
chart show the handle of the range lever pointing
to "I" or "II", which appears opposite of the actual
configuration of the lever. If requiring the "I" posi-
tion as directed in the chart, point the arrow on the
lever hub to 1/LO (low). Conversely, if the chart
directs you to select the "II" position, point the
arrow at 2/HI (high).
Figure 59.;ZZYgViZgVc\ZaZkZg#