Grizzly G97030 Lathe User Manual


  Open as PDF
of 130
 
BdYZa<.,(%$<.,(&B[\#H^cXZ.$%%
"'*"
10. BdkZ i]Z he^cYaZ heZZY gVc\Z aZkZg id i]Z
adl g^\]i edh^i^dc! VcY gdiViZ i]Z he^cYaZ
heZZY`cdWhdi]Vii]ZVggdled^cihid&%*
hZZFigure 21#
11. Ijgci]ZbVhiZgedlZghl^iX]ON#
12. GZhZii]ZZbZg\ZcXnHIDEWjiidcWnil^hi"
^c\^iXadX`l^hZjci^a^iedehdji·i]ZedlZg
a^\]idci]ZXdcigdaeVcZah]djaY^aajb^cViZ#
13. KZg^[ni]Vii]ZbVX]^cZ^hdeZgVi^c\XdggZXian
Wnejaa^c\i]Zhe^cYaZDC$D;;aZkZgdjiVcY
YdlcidhiVgihe^cYaZgdiVi^dc#
·L]Zc deZgVi^c\ XdggZXian! i]Z aVi]Z gjch
hbddi]anl^i]a^iiaZdgcdk^WgVi^dc#
·>ckZhi^\ViZVcYXdggZXihigVc\ZdgjcjhjVa
cd^hZh dg k^WgVi^dch WZ[dgZ deZgVi^c\ i]Z
aVi]Z[jgi]Zg# 6alVnhY^hXdccZXii]Z aVi]Z
[gdbedlZgl]Zc^ckZhi^\Vi^c\dgXdggZXi"
^c\ediZci^VaegdWaZbh#
14. For the Model G9731 Only:L^i]i]Zhe^cYaZ
DC$D;;aZkZg^ci]ZYdlcedh^i^dc!i]Zhe^c"
YaZ h]djaY WZ gdiVi^c\ XdjciZgXadX`l^hZ·
YdlcVcYidlVgYndjVhndj[VXZi]ZaVi]Z#
·>[i]Zhe^cYaZ^hcdigdiVi^c\XdjciZgXadX`"
l^hZl^i]i]Zhe^cYaZDC$D;;aZkZg^ci]Z
Ydlcedh^i^dc!i]ZedlZghjeean]VhWZZc
XdccZXiZY dji d[ e]VhZ# Hide i]Z aVi]Z!
ijgci]ZbVhiZgedlZghl^iX]OFF!Y^hXdc"
cZXii]ZaVi]Z[gdbedlZg!i]Zc[daadli]Z
^chigjXi^dch ^c Phase Polarity dc Page
14#
6[iZgXdggZXi^c\i]Z l^g^c\!gZeZVihSteps
11–14#
15. BdkZi]Zhe^cYaZDC$D;;aZkZgidi]ZD;;
b^YYaZedh^i^dc!egZhhi]ZZbZg\ZcXnHIDE
Wjiidc ^c! i]Zc ViiZbei id gZ"hiVgi he^cYaZ
gdiVi^dc#
·>[ i]ZaVi]Z YdZh cdi hiVgi l^i] i]Z ZbZg"
\ZcXnHIDEWjiidcegZhhZY^c!i]^hhV[Zin
[ZVijgZ^hldg`^c\egdeZgan#
·>[i]ZaVi]ZYdZhhiVgil^i]i]ZZbZg\ZcXn
HIDEWjiidcegZhhZY^c!i]^hhV[Zin[ZVijgZ
^hcdideZgVi^c\XdggZXian#I]ZZbZg\ZcXn
HIDEWjiidcbjhideZgViZegdeZganWZ[dgZ
Xdci^cj^c\deZgVi^dc#JhZi]Zhe^cYaZDC$
D;;aZkZgidhidei]ZaVi]Z!ijgci]ZbVhiZg
edlZg hl^iX] OFF! Y^hXdccZXi i]Z aVi]Z
[gdb edlZg! i]Zc XVaa IZX] Hjeedgi [dg
]Zae#
16. GZhZi i]ZZbZg\ZcXnHIDEWjiidc!gZ"hiVgi
he^cYaZ gdiVi^dc! i]Zc egZhh i]Z [ddi WgV`Z#
I]Z aVi]Z h]djaY ijgc OFF VcYi]Z he^cYaZ
h]djaYXdbZidVfj^X`hide#
Note: After using the foot brake to stop the
lathe, it is necessary to move the spindle
ON/OFF lever to the OFF position before
attempting to re-start spindle rotation.
17. Ed^ci i]Z Xjii^c\ [aj^Y cdooaZ Ydlc ^cid i]Z
X]^eigVn!jhZi]ZXjii^c\[aj^Yhl^iX]dci]Z
Xdcigda eVcZa id hiVgi i]Z ejbe! i]Zc deZc
i]ZkVakZdci]ZcdooaZ#KZg^[ni]Vii]ZXjii^c\
[aj^Y [adlh[gdb i]Z cdooaZ VcYegdeZgan gZ"
XnXaZhidi]ZXjii^c\[aj^YgZhZgkd^g!i]Zcijgc
i]ZejbeOFF#
8dc\gVijaVi^dchI]ZiZhigjc^hXdbeaZiZ#8dci^cjZ
l^i] i]Z Spindle Break-InVcYRecommended
AdjustmentsegdXZYjgZhdci]ZcZmieV\Z#
NOTICE
During the first 16 hours of use, the V-belts
will stretch and seat into the pulley grooves.
The V-belts must be properly re-tensioned
after this period to avoid reducing their use-
ful life. Refer to V-Belts Service on Page 83
for detailed instructions.
 previous next