Grizzly G97030 Lathe User Manual


  Open as PDF
of 130
 
"+%"
BdYZa<.,(%$<.,(&B[\#H^cXZ.$%%
Cutting Fluid System
L]Zci]ZXjii^c\[aj^Yejbehl^iX]^hijgcZYON!
i]Z[aj^Y^hYZa^kZgZYi]gdj\]i]ZcdooaZViiVX]ZY
idi]ZXVgg^V\Z!VcYi]Z[adl^hXdcigdaaZYWni]Z
kVakZaZkZgVii]ZWVhZd[i]ZcdooaZ#I]ZXjii^c\
[aj^Y YgV^ch ^cid i]Z X]^e igVn VcY i]gdj\] i]Z
hXgZZc WVX` ^cid i]Z Xjii^c\ [aj^Y gZhZgkd^g hZZ
Figure 93#
6alVnhjhZ]^\]fjVa^inXjii^c\[aj^Y^ci]ZXjii^c\
[aj^YhnhiZbVcY[daadli]ZbVcj[VXijgZgh^chigjX"
i^dch[dgY^aji^c\#I]Zfj^X`gZ[ZgZcXZiVWaZWZadl
XVc]ZaendjhZaZXii]ZVeegdeg^ViZXjii^c\[aj^Y#
8]ZX` i]Z Xjii^c\ [aj^Y gZ\jaVgan VcY egdbeian
X]Vc\Z^il]Zc^iWZXdbZhdkZganY^gindggVcX^Y!
dg Vh gZXdbbZcYZY Wn i]Z [aj^Y bVcj[VXijgZg
hZZCutting Fluid System ServicedcPage 69
[dgYZiV^aZY^chigjXi^dch#
BIOLOGICAL & POISON
HAZARD!
Use the correct person-
al protection equipment
when handling cutting
fluid. Follow federal,
state, and fluid manu-
facturer requirements
for proper disposal.
NOTICE
Running the cutting fluid pump without
adequate fluid in the reservoir may perma-
nently damage it, which will not be covered
under warranty.
To use the cutting fluid system:
1. BV`ZhjgZi]ZXjii^c\[aj^YgZhZgkd^g^hegde"
Zgan hZgk^XZY VcY [^aaZY! VcY i]Vi ndj VgZ
lZVg^c\ i]Z cZXZhhVgn eZghdcVa egdiZXi^dc
Zfj^ebZci#
2. Edh^i^dc i]Z [aj^Y cdooaZ [dg ndjg deZgVi^dc!
i]ZcjhZi]ZXjii^c\[aj^Yejbehl^iX]dci]Z
XdcigdaeVcZaidi]Zijgci]ZejbeON#
3. 6Y_jhi i]Z [adl d[ [aj^Y Wn jh^c\ i]Z kVakZ
aZkZgVii]ZWVhZd[i]ZcdooaZ]dhZ#
Important: EgdbeianXaZVcVcnheaVh]ZY[aj^Y
[gdbi]Z[addgidegZkZciVha^ee^c\]VoVgY#
Figure 93.8jii^c\[aj^YhnhiZbXdbedcZcih#
8jii^c\;aj^Y
GZhZgkd^g
CdooaZ
KVakZ
EjbeHl^iX]
Workpiece Dry
Water
Soluble Oil
Synthetic
Fluids
Sulferized Oil Mineral Oil
6ajb^cjb M M
7gVhh MMM
7gdcoZ M M M M
8Vhi>gdc M
Adl8VgWdcHiZZa M M
6aadnBZiVah MMMM
HiV^caZhhHiZZa MMMM
General Note: Cutting fluids are used for heavy-duty lathe operations and production turning. Oil-water emulsions and synthetic
cutting fluids are the most common for typical lathe operations. Sulferized oils often are used for threading. For small projects,
spot lubrications can be done with an oil can or brush, or omitted completely.
 previous next