Filter
Top Products
SpeedMill 5
2 –
English
KEY TO SYMBOLS
Key to symbols
WARNING! The machine can be a
dangerous tool if used incorrectly or
carelessly, which can cause serious or fatal
injury to the operator or others.
Please read the operator’s manual carefully
and make sure you understand the
instructions before using the machine.
Always wear:
• Protective helmet
• Hearing protection
• Protective goggles or a visor
WARNING! Dust forms when cutting, this
can cause injuries if inhaled. Use an
approved breathing mask. Avoid inhaling
petrol fumes and exhaust fumes. Always
provide for good ventilation.
WARNING! Sparks from the cutting blade
can cause fire in combustible materials
such as: petrol (gas), wood, dry grass etc.
Switch off the engine by moving the stop
switch to the STOP position before carrying
out any checks or maintenance.
Always wear approved protective gloves.
Regular cleaning is required.
Visual check.
Protective goggles or a visor must be worn.
Run position.
Stop, with the return spring to the operating
position.
Stop, in the fixed position.
Other symbols/decals on the machine refer to special
certification requirements for certain markets.
SAFETY INSTRUCTIONS
WARNING!
Read, understand, and follow all warnings and instructions in this and the K750 manuals. Failure to do so may result
in serious personal injury as well as damage to the equipment. It is not possible to cover all possible risk situations that
can arise in conjunction with pipe cutting and beveling within these instructions. Use common sense and caution at all
times.
Remember: “If you don’t know – don’t do.”
The SpeedMill may not be modied from its original design without the manufacturer’s approval in writing. Unapproved
modications can result in serious injury.
All operators must be trained in the proper use of this machine. It is the owner’s responsibility to explain the content of
this manual to all operators and ensure that they receive the necessary training to safely operate this machine.
PERSONAL SAFETY
Stay alert; watch what you are doing, and use common sense when operating this SpeedMill or any other
power tool. Do not use when tired or under the inuence of drugs, alcohol, or medication, or any substance that could
affect your judgment. A moment of inattention during operation may result in serious personal injury.
Keep proper footing and balance at all times. Do not overreach or operate from a ladder. Do not operate above
chest height. If necessary use proper scaffolding to reach a safe operating height.
Use personal safety equipment. Always wear eye protection, hard hat, hearing protection, non-slip safety shoes and
gloves. Respirator mask must be used when dry-cutting. (Reference OSHA 29CFR 1910.95, 1910.133-138)
Dress properly. Never wear loose clothing or jewelry. Keep long hair tied back. Keep your hair, clothing, and gloves
away from the rotating blade.
Do not use the SpeedMill if the ON/OFF switch does not turn it on or off. Have the switch replaced before the
SpeedMill is used again.
WORK AREA SAFETY
Keep the work area organized. Maintain a rm grip of the SpeedMill and have a proper footing and balance at all
times.
Do not operate your SpeedMill in an explosive atmosphere. Sparks may ignite ammable liquids,
gases, or dust. This is a concern when old pipes are being repaired.
Keep all bystanders at a safe distance. Bystanders can be a distraction that can cause you to lose control.
CHOICE OF BLADE
Use only 12” high speed abrasive concrete cutting blades for cutting specied PVC pipe with the SpeedMill.
Use only blades designated High Speed blades with a minimum speed rating of 6300 rpm. Many blades are not made
for hand held high speed saw and they all have a lower speed rating (marked on their label) Such blades might brake
at higher speed with possible severe injury as a result.
Diamond blades shall not be used while cutting any plastic pipe due to the increased risk of “kick-back”. (Regard-
ing kick-back see K750 operation manual).
Use of carbide tipped blades or any blade with cutting teeth, is a violation of OSHA regulations and shall never be used.
The operator must
wear protective
clothing
appropriate to the
work he is doing.