Filter
Top Products
6
• Check that the water-cooling coupling matches the speci-
fications. See section 9 Technical specifications.
• Set up a barrier or signs around the working area to
prevent any unauthorised personnel from being injured
or disturbing the operator while working.
• Check the belt tension as described in section 5.5. Adjust
if necessary using the belt tensioning screw. Turning
clockwise tightens the belts.
• Before you start cutting, plan your work and clearly mark
out the area you intend to cut so that you can carry out
the work without risk of injury or damage to the machine.
See figure 3.1.
• To avoid interruptions and inconvenience during cutting,
plan your work so that you fit the blade on the most suita-
ble side of the saw right from the start.
• Check that you have the correct diamond blade for the
FS800 E/EM and the material you intend to cut. See
section 9 Technical specifications.
• Check the direction of rotation before fitting the blade.
Raise the blade guard on the side where you want to fit
the blade. Secure the blade guard with the retaining
strap. Connect the power cable and press the switch to
start the machine. Check that the blade flange rotates in
the direction shown by the arrow on the blade guard. If
the flange rotates in the wrong direction, turn off the
switch to stop the machine, then unplug the power cable
from the machine. Turn the phase inverter in the socket.
Stop the machine as described above and recheck.
• Check that the blade is not worn; each of the diamond
segments must project at least 1 mm. They must also be
wider than the body of the blade. See figure 6.3.
• Check that none of the diamond segments is damaged.
• Fit the blade so that the arrow on the body of the blade
matches the direction of rotation of the shaft. Tighten
the blade flange using the pin spanner supplied, while
using the other spanner to prevent the blade shaft from
turning. See the instructions in section 6, Fitting and
replacing diamond blades. See figure 6.1.
• Lower the blade guard over the blade.
• Check that the blade is straight by turning the blade by
hand and measuring the gap between the blade and the
blade guard. If the blade is misaligned or uneven it must
be replaced.
• Check that both the blade guard and the blade flange
guard are correctly fitted, then lower them.
• Make sure the emergency stop is not deactivated. The
emergency stop must not be deactivated during operation.
• Before starting the floor saw, raise the blade so that it
rotates without touching the surface.
• Connect the power cable to the power socket.
• Connect the water-cooling hose to the coupling that runs
from the blade guard.
• Check that the water supply is adequate and that the
nozzle is not blocked.
• Make sure that the power cable and water-cooling hose
from the floor saw will not get trapped underneath or in
front of the machine when you start up or during cutting.
• Use the safety equipment specified in the safety precau-
tions on page 5.
Figure 3.1.
4. Starting and operating
Before starting and operating the saw follow the steps in
section 3.
• Lower the alignment guide and adjust it so that the tip of
the guide and the saw blade are in line.
• Release the parking brake.
• Line up the floor saw with the cutting line you have
marked on the floor.
• Clear away any objects from the path of the machine that
could damage the machine or the surroundings.
• Check that there are no unauthorised people inside the
working area, i.e. 4 metres in front of and to the side of
the machine.
• Make sure that anyone who has to remain nearby is
wearing hearing protection.
• Check that the saw blade rotates freely.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
WARNING
Make sure that you are not
working on a floor that could
give way underneath you.
WARNING
Do not cut on a steep
incline as the blade
could jam.
WARNING
Do not use the saw where
there is a risk of collapse.