Ingersoll-Rand GRG15M06G7 Grinder User Manual


 
M10
180
4–30–94
11–4–99
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
SECTION
MANUAL
Released:
Revised:
R
For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll–Rand Distribution Center,
White House, TN at PH: (615) 672–0321, FAX: (615) 672–0801
ARO Tool Products
Ingersoll–Rand Company
1725 U.S. No. 1 North, PO Box 8000, Southern Pines, NC 28388–8000
1999 INGERSOLL–RAND COMPANY PRINTED IN U.S.A
MODELS GRG15A–06G–7, GRG15A–06G–9, GRG15A–08G–7,
GRG15M–06G–7, GRG15M–06G–9, GRG15M–08G–7,
GRP15A–02P–7, GRS15A–04S–9, AND GRS15A–06S–7
1.5 H.P. ANGLE GRINDERS, POLISHERS, AND SANDERS
GRG Air Angle Grinders, GRS Air Angle Sanders and GRP Air Angle polishers are designed for smooth-
ing, trimming or removing metal in close–quarter areas in foundries, shipyards, steel mills and in
construction applications.
ARO is not responsible for customer modification of tools for applications on which ARO was not
consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/10” (10 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig (6.2 bar/
620 kPa) maximum air pressure. Dust, corrosive
fumes and/or excessive moisture can ruin the
motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away
from rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Tool accessories may continue to rotate briefly
after throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain oc-
curs. Seek medical advice before resuming use.
Use accessories recommended by ARO.
Whenever the Angle Head is installed or reposi-
tioned, the Throttle Lever must be positioned so
that reaction torque will not tend to retain the
throttle in the “ON” position.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
The use of other than genuine ARO replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest ARO Tool Products Authorized
Servicenter.
F
E
P
F
E
P