Filter
Top Products
RReegguullaarrllyy cclleeaann tthhee vveennttiillaattiioonn sslloottss iinn yyoouurr ttooooll aanndd cchhaarrggeerr uussiinngg oonnllyy aa ssoofftt
bbrruusshh oorr ddrryy ccllootthh.
.
NNeevveerr ooppeenn tthhee CCoorrddlleessss DDrriillll ccaassee,, bbaatttteerryy ppaacckk oorr cchhaarrggeerr..
Do not attempt to
repair the Cordless Drill, battery pack or charger yourself. Opening any of these
parts will void your warranty.
AACCCCEESSSSOORRIIEESS
UUssee oonnllyy aacccceessssoorriieess tthhaatt aarree rreeccoommmmeennddeedd bbyy tthhee mmaannuuffaaccttuurreerr ffoorr yyoouurr mmooddeell..
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
AAllwwaayyss a
attttaacchh ggrroouunnddeedd ((33--pprroonngg)) eexxtteennssiioonn ccoorrddss ttoo ggrroouunnddeedd ((33--hhoollee)) oouuttlleettss..
IIff yyoouu mmuusstt uussee aann eexxtteennssiioonn
ccoorrdd,, bbee ssuurree tthhaatt tthhee ggaauuggee iiss llaarrggee eennoouugghh ttoo ccaarrrryy
tthhee aammoouunntt ooff ccuurrrreenntt nneecceessssaarryy ffoorr yyoouurr ppoowweer
r ttooooll..
If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on next page).
RREECCOOMMMMEENNDDEEDD SSIIZZEESS OOFF EEXXTTEENNSSIIOONN CCOORRDDSS 112200 VVOOLLTT AACC 6600 HHZZ TTOOOOLLSS
TTOOOOLL CCUURRRREENNTT RRAATTIINNGG CCOONNDDUUCCTTOORR SSIIZZEE IINN AA..WW..GG
AMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 18
6-8 18 18 18 16
8-10 18 18 18 14
10-12 16 16 14 14
12-16 14 12 12 -
16-20 12 12 12 -
18
• Just before the drill tip breaks though the other side of the work piece drill more
slowly and decrease pressure on the tool. This will prevent stalling and leave a
cleaner hole.
• Use a block of wood to back up work pieces that may splinter.
• Use spade bits when drilling large diameter holes in wood.
• Use HSS drill bits when drilling in metal.
• Use masonry bits when drilling in soft masonry.
• Use a lubricant when drilling metals other than cast iron, aluminum, copper,
and brass.
• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent
slipping at higher speeds.
• Never try to start a stalled Drill by clicking the trigger switch
““OONN””
and
““OOFFFF””
.
This may damage your tool.
• To reduce jamming, always keep the Drill running when pulling the bit out of a
finished hole.
SSCCRREEWWDDRRIIVVIINNGG::
• Always use the correct type and size of screwdriver bit.
• If screws are difficult to tighten, try applying a small amount of washing liquid or
soap as a lubricant.
• Always hold the tool and screwdriver bit in a straight line with the screw.
MMAAIINNTTEENNAANNCCEE AANNDD CCLLEEAANNIINNGG
AAllwwaayyss rreemmoovvee tthhee bbaatttteerryy ppaacckk bbeeffoorree aatttteemmppttiinngg
cclleeaanniinngg oorr mmaaiinntteennaannccee..
TT
hhiiss CCoorrddlleessss DDrriillll iiss lluubbrriiccaatteedd bbeeffoorree iitt lleeaavveess tthhee
ffaaccttoorryy..
This lubrication should last for the life of the tool. No further
lubrication is required.
UUssee oonnllyy mmiilldd ssooaapp aanndd aa ddaammpp cclloot
thh ttoo cclleeaann tthhee ttooooll..
Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
AAllwwaayyss cclleeaann tthhee bbaatttteerryy ppaacckk uussiinngg oonnllyy aa ddrryy ccllootthh.. DDoo nnoott uussee lliiqquuiiddss..
AAl
lwwaayyss uunnpplluugg tthhee cchhaarrggeerr bbeeffoorree cclleeaanniinngg iitt..
17