Filter
Top Products
VVAARRIIAABBLLEE SSPPEEEEDD TTRRIIGGGGEERR SSWWIITTCCHH
TTHHIISS TTOOOOLL IISS CCOONNTTRROOLLLLEEDD
BBYY AA TTRRIIGGGGEERR SSWWIITTCCHH::
• The speed of the Cordless Drill depends
on the amount of pressure you put on the
trigger.
• The more pressure you apply, the faster
the Cordless Drill will go.
• Release the pressure and the Cordless
Drill will slow down.
BBUUIILLTT IINN LLEEDD LLAAMMPP
• Press the trigger switch to light up the lamp. The lamp remains on while the
trigger switch is being pressed. The lamp goes out after releasing the trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch
the lens of lamp, or it may lower the illumination.
Do not look into light or see the source of light directly.
FFOORRWWAARRDD// RREEVVEERRSSEE AANNDD TTRRIIGGGGEERR LLOOCCKK LLEEVVEERR
BBee ssuurree tthhee ttrriiggggeerr iiss rreelleeaasseedd wwhheenn cchhaannggiinngg tthhee ppoossiittiioonn oof
f tthhee lleevveerr..
Always store the tool in the
““LLOOCCKKEEDD//OOFFFF””
position.
AAllwwaayyss cchheecckk tthhee ddiirreeccttiioonn ooff tthhee CCoorrddlleessss DDrriillll''ss rroottaattiioonn bbeeffoorree uussee..
TT
OO SSEELLEECCTT TTHHEE DDIIRREECCTTIIOONNSS
OOFF RROOTTAATTIIOONN::
• To select forward Cordless Drill
rotation, press the trigger lock from
left to right flat against the Cordless
Drill body.
• To select reverse, press the trigger
lock lever in the opposite direction.
• The center position locks the tool.
IINNSSTTAALLLLIINNGG DDRRIILLLL BBIITT IINNTTOO KKEEYYLLEESSSS CCHHUUCCKK
BBeeffoorree iinnsseerrttiinngg aa ddrriillll bbiitt oorr ootthheerr aacccceessssoorryy,,
make sure the forward/reverse
and trigger lock lever is in the center
““OOFFFF””
position to prevent accidental starts
that may result in injury.
DD
oo nnoott aatttteemmpptt ttoo ttiigghhtteenn ddrriillll bbiittss ((oorr aannyy ootthheerr aacccceessssoorryy)) bbyy ggrriippppiinngg tthhee
ffrroonntt ooff tthhee cchhuucckk aanndd t
tuurrnniinngg tthhee ttooooll oonn..
This may cause personal injury
and/or damage to the chuck.
WWhheenn rreemmoovviinngg tthhee bbiitt ffrroomm tthhee ttooooll,, aavvooiidd ccoonnttaacctt wwiitthh sskkiinn aanndd uussee pprrooppeerr
ppr
rootteeccttiivvee gglloovveess wwhheenn ggrraassppiinngg tthhee bbiitt oorr aacccceessssoorryy..
Accessories may be hot
after prolonged use.
1. Hold the rear end of the chuck in
one hand and use the other hand to
rotate the front end in a counter-
clockwise direction to open the jaws
of the chuck.
2. Insert the shank of the bit (or other
accessory) fully into the keyless
chuck, taking care to keep the bit in
the center of the jaws of the chuck.
3. Turn the front end of the chuck clockwise
to hold the bit in place.
4. Tighten securely by turning the front end of the chuck clockwise while holding
the rear end.
OOPPEERRAATTIINNGG TTHHEE DDRRIILLLL
NNeevveerr ttaappee tthhee ttrriiggggeerr sswwiittcchh ddoowwnn ttoo pprroovviiddee ccoonnttiinnuu--
oouuss hhiigghh ssppeeeedd..
The tool may fail under such conditions causing fire or
personal injury.
WARNING
13
TRIGGER
LOCK
TRIGGER
SWITCH
LED LIGHT
HOLD HERE
HOLD HERE
RELEASE
GRIP
FORWARD
LOCK
REVERSE