Filter
Top Products
OOPPEERRAATTIINNGG TTHHEE AANNGGLLEE GGRRIINNDDEERR
AAllwwaayyss uunnpplluugg tthhee ttooooll bbeeffoorree aatttteemmppttiinngg ttoo cchhaannggee tthhee
gguuaarrdd oorr aacccceessssoorriieess..
For best tool control, material removal and minimal
loading, keep the angle between the disc and the work surface at approximate-
ly 30° when grinding and 10°-15° when sanding.
OOPPEERRAATTIINNGG TTHHEE OONN//OOFFFF SSWWIITTCCHH
NNeevveerr sswwiittcchh tthhee AAnnggllee GGrriinnddeerr ““OONN”” oorr ““OOFFFF”” wwhhiillee
uunnddeerr llooaadd ccoonnddiittiioonnss..
AAllwwaayyss aallllooww tthhee AAnnggllee GGrri
innddeerr ttoo ccoommee uupp ttoo ffuullll ssppeeeedd bbeeffoorree ttoouucchhiinngg aannyy
ssuurrffaaccee..
AAllwwaayyss ttaakkee tthhee ttooooll aawwaayy ffrroomm tthhee wwoorrkkp
piieeccee bbeeffoorree ttuurrnniinngg tthhee ttooooll ““OOFFFF””..
Let the tool come to a complete stop before setting it down.
TThhiiss ttooooll ooppeerraatteess bbeesstt uunnddeerr lliigghhtt pprreessssuurree..
Exerting heavy pressure will not
speed up the work and may cause damage to the motor.
PPrreessss tthhee ““OONN//O
OFFFF”” sswwiittcchh ttoo ssttaarrtt tthhee ttooooll..
TToo ssttoopp,, rreelleeaassee tthhee ““OONN//OOFFFF”” sswwiittcchh..
When continuous operation
is desired, press the
““OONN//OOFFFF””
switch forward
and depress the lock-on but-
ton. This locks the switch
““OONN””
until the lock-on but-
ton is released.
12
AATTTTAACCHHIINNGG WWIIRREE BBRRUUSSHHEESS
Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are
necessary.
EEDDGGEE GGRRIINNDDIINNGG
DDoo nnoott uussee eeddggee ggrriinnddiinngg wwhheeeellss ffoorr ccuutt--ooffff wwoorrkk,, ddeeeepp
ggrriinnddiinngg oorr ssuubbjjeecctt tthheemm ttoo aannyy ssiiddee pprreessssuurree
aass tthhiiss mmaayy lleeaadd ttoo bbrreeaakkaaggee
aanndd ppoossssiibbllee ppeerrssoonnaall iinnjjuurryy..
These wheels should be used for shallow cutting
and notching (less than 1/2" in depth). Keep the open side of the guard away
from the operator at all times.
Edge grinding should only be done with wheels specifically designed for this purpose.
RREEMMOOVVIINNGG GGUUAARRDD FFOORR SSAANNDDIINNGG OORR UUSSIINNGG FFLLAATT WWIIRREE BBRRUUSSHHEESS
• Set the Angle Grinder on a flat surface with the spindle facing up.
• Remove the inner and outer flanges, unscrew spring washer and remove
the guard.
• Store these parts carefully.
• Replace the guard after the job is finished.
AATTTTAACCHHIINNGG SSAANNDDIINNGG DDIISSCC
• To remove the guard, see instructions given in the “Removing Guard for Sanding
or Using Flat Wire Brushes” Section above.
• Set the inner flange and outer flange on the spindle.
• Push in the spindle lock button. Turn the spindle until it locks into place.
• Once the spindle is locked, tighten the sanding disc by hand.
WARNING
11
ON/OFF
SWITCH
LOCK-ON
BUTTON