Filter
Top Products
13
A method of checking the correct cut-
ting depth is to lay a piece of the
material you plan to cut along the side
of the blade and observe how much
tooth projects beyond the material.
BEVEL ANGLE ADJUSTMENT
Disconnect plug from power supply before making any
adjustments to the tool.
The full range of bevel adjustment is from 0
to 45 DEGREES. The quadrant is graduated
in increments of 5 degrees.
On the front of the saw is a bevel angle
adjustment mechanism consisting of a cali-
brated quadrant and a knob.
To set the saw for a bevel cut, turn the
bevel adjustment knob counterclockwise
to loosen, and tilt shoe to the desired
angle by aligning the pointer with the
desired angle mark. Retighten knob firmly
by turning it clockwise.
LLAASSEERR GGUUIIDDEE
Use of controls or procedures, or performance of proce-
dures other then those specified herein may result in hazardous radiation
exposure.
LLAASSEERR SSAAFFEETTYY
NNEEVVEERR LLOOOOKK IINNTTOO TTHHEE LLAASSEERR BBEEAAMM..
Any contact with the eyes by the beam
could cause injury. Do not use the laser when cutting reflective materials.
DDOO NNOOTT AAIIMM TTHHEE LLAASSEERR BBEEAAMM AATT AANNYYOONNEE OORR AATT RREEFFLLEECCTTIIVVEE
SSUURRFFAACCEESS..
CCLLAASSSS 22MM LLAASSEERR PPRROODDUUCCTT..
Any contact with the eyes by the beam could
cause injury. Ensure the laser beam is turned on only when the tool is on a non-
reflective workpiece and as such it is aimed only at the work surface. Metals and
other materials like steel which can be highly reflective should only be cut with-
out the use of the laser.
SSTTOORREE OOUUTT OOFF RREEAACCHH OOFF CCHHIILLDDRREENN..
Equipment should be in a high location
or locked up to keep out of reach of children. It is not a toy.
DDOO NNOOTT TTAAMMPPEERR WWIITTHH TTHHEE LLAASSEERR O
OUUTTPPUUTT..
Changing the performance of the
laser to increase its output is prohibited. Any claim for damages or injuries
resulting from not following these instructions will be refused.
OOPPEERRAATTIIOONN AACCCCEESSSSIIBBLLEE FFIIEELLDDSS::
Wavelength 636-660nm
Laser Power for Classification <1mW CW
NNEEVVEERR OOPPEERRAATTEE LLAASSEERR IIFF TTHHEE UUNNIITT IISS DDEEFFEECCTTIIVVEE OORR TTHHEE CCOOVVEERR OOR
R SSEEAALL
IISS DDAAMMAAGGEEDD..
DDOO NNOOTT SSEERRVVIICCEE LLAASSEERR..
The laser unit must be returned to the factory for any
service or repair. Service or repair must be handled by authorized factory
trained technicians.
Do not open the laser unit except to change batteries.
RREEMMOOVVEE BBAATTTTEERRIIEESS IIFF TTHHEE LLEEVVEELL IISS TTOO BBEE SSTTOORREEDD FFOORR AANNYY LLEEN
NGGTTHH OOFF
TTIIMMEE..
Batteries may leak and damage the laser if it is stored idle for more than
3 months.
Be careful with this tool. Striking or jarring it, especially on the laser housing,
can affect its accuracy.
Other than batteries, there are no user-serviceable parts in the laser device.
L
ASER LIGHT
DO N
O
T
VIEW
DIREC
TL
Y WITH OP
TIC
A
L
IN
S
T
RUM
E
NT
S
(M
A
GNIFIER
S
)
C
L
A
S
S 2
M
L
ASE
R
PRODU
C
T
635-66
0
n
m
, <1m
W
CW
C
LAS
S
I
FIEDS P
ER I
E
C
6
0825-1,
E
d. 1.2, 200
1
-
0
8
AV
O
ID
E
XP
O
S
U
R
E -
LA
S
ER
L
IG
H
T IS
E
M
IT
TED
FR
O
M
T
H
IS A
P
ER
T
UR
E.î
LASER RADIATION
CAUTION LABEL
14
LOCK