Filter
Top Products
Operating Instructions
Read and understand these directions thoroughly before
attempting to operate the water heater. Make sure the view port
is not missing or damaged (See Figure 36). Make sure the tank
is completely filled with water before operating the water heater.
The gas control valve/thermostat has a "On/Off Switch" and
needs to be turned on before water heater is operational. Check
the label on the front of heater near the gas control valve/
thermostat for the correct gas. Do not use this water heater with
any gas other than the one listed on the label. If you have any
questions or doubts, consult your gas supplier or gas utility
company.
Explosion Hazard
Replace view port if glass is missing
or damaged.
Failure to do so can result in death,
explosion or fire.
FIGURE 28.
FO-=RYOUR SAFETY READ BEFORE OPERATING
BEFOREOPERATING:ENTIRESYSTEMMUST BEFILLEDWITH WATERAND AIR PURGEDFROMALL LINES.
A. Thisappliancedoesnothavea pilot. Itis equippedwith • If you cannot reach your gas supplier, call the
a.
an ignition device that will automatically light the
burner. Do not try to light the burner by hand.
BEFORE OPERATINGsmellall aroundthe appliance
areafor gas. Be sureto smell nextto thefloorbecause
some gas is heavierthan airandwill settle onthefloor.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electric switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
fire department.
C. Useonly your hand to push inthe electronic display i
buttons and gas control switch. Never use tools.
If the control buttons will not push in, don't try toi
repair them, calla qualified service technician. Forcei
or attempted repair may result ina fire or explosion.
D. Do not use this appliance if any part has been
under water. Immediately contact a qualified
installer or service agency to replace a flooded
water heater. Do not attempt to repair the unit.
phone. Follow the gas supplier's instructions. !t_M#$ be rep!aoed!
OPERATING INSTRUCTIONS _ q!
[ L _----ONiOFF
SWITCH
"GAS CONTROL"
1 STOP! Read the safety information
above on the label.
2. Turn on all electrical power to the appliance.
3. Set the ON/OFF switch on the gas control to the
"ON" position.
4. Set the Electronic Display to the lowest
setting by [jrst pressing the COOLER _ and
HOTTER _ buttons together and holding for 1
second. Then press the COOLER (v) button to
the lowest setting.
5. Set the ON/OFF switch on the gas control to the
"OFF" position.
6. This appliance is equipped with a device
which automatically lights the burner.
DO NOT TRY TO LIGHT THE BURNER BY HAND.
7. Wait five (5) minutes to _ clear out any gas.
tf you then smell gas_STOP! Follow "B" in
the safety information above on this label. If you
don't smell gas, go to the next step.
q
I:oo !
@@
"ELECTRONIC DISPLAY"
8. Set the ON/OFF switch on the gas control to the
"ON" postition.
9. Set the ElectronicDisplayto_the desiredsettingby first
pressing the COOLER U and HOTTER (,O)but-
tons together and holding for 1second. Then press
the HOTTER C) button until the desired setting
is reached.
manual before changing temperature.
10. Ifthe appliance will not operate, follow the instruc-
tions "TO TURN OFF GAS TO APPLIANCE" and
call your technician or gas supplier.
1. Set the Electronic Display tothe lowestsettingby first 2. Set the ON/OFF switch on the gas control to the
pressing the COOLER (v) and HOTTER (_) but-
tons together and holding-for 1second. Then press "OFF"postition.
the COOLER C) button to the lowest setting. 3. Turn offall electrical power to the appliance if
service is to be performed.
25