Filter
Top Products
$)*""*%$
(403C78B4=C8A48=BC0;;0C8>=B42C8>=145>A4H>D
BC0AC8=BC0;;0C8>=
)*.&(+*%$)
"*(T)%! 20=:8;;
N0E40=4;42CA8280=8=BC0;;0=3
B4AE824C78B4@D8?<4=C
N*DA=C748=?DC?>F4A>550CC74
5DB4 1>G 145>A4 F>A:8=6 >=
4@D8?<4=C
N>=>CC>D274;42CA820;;H7>C?0ACB
N4BDA4C>38B270A6420?028C>ABF8C7C74?A>24
3DA4>DC;8=438=C74#08=C4=0=24)42C8>=>5C78B
<0=D0;145>A4F>A:8=68=C70C0A40>5C74
4@D8?<4=C
-----------------------------------------------------------------------
)"*)+*""%*%$
The ES 275i will operate in harsh environments. Even
so, it is important that simple preventative measures
are followed in order to assure long life and reliable
operation.
• The machine must be located where there is free cir-
culation of clean air such that air movement in the
back and out the front will not be restricted.
• Dirt and dust that can be drawn into the machine
should be kept to a minimum. Failure to observe
these precautions can result in excessive operating
temperatures and nuisance shutdown.
• Keep machine dry. Shelter from rain and snow. Do
not place on wet ground or in puddles.
N%$%*#%+$*%,(%#+)*")+()
-74A4C74A48B02><1DBC81;4BDA502438A42C;H
D=34ABC0C8>=0AH>A58G434;42CA820;4@D8?<4=C
C70CBDA5024B70;;142>E4A43F8C70BC44;?;0C40C
;40BCR<<C782:F7827B70;;4GC4=3=>C
;4BBC70=R<<14H>=3C744@D8?<4=C>=
0;;B834B
-----------------------------------------------------------------------
)*!$
ES 275i’s cannot be stacked.
*"*$
Place the machine directly on a secure, level surface.
The machine may topple over if this procedure is not
followed.
('+$.&(%**%$
Locate the ES 275i away from radio controlled
machinery.
*74=>A<0;>?4A0C8>=>5C74)8<0H03E4AB4
;H05542CC74>?4A0C8>=>5(2>=CA>;;434@D8?<4=C
F7827<0HA4BD;C8=1>38;H8=9DAH>A30<064C>C74
4@D8?<4=C
-----------------------------------------------------------------------
$&+*%$$*%$)
The ES 275i should be connected only by a qualified
electrician. Installation should be made in accordance
with all local and national electric codes and the infor-
mation detailed below.
$&+*+)$)+&&".-(
Refer to the *427=820;)?4285820C8>=B page at the
beginning of this chapter for the proper fuse sizes and
supply cable sizes.
• Fuse the input circuit with recommended super lag
fuses or delay type circuit breakers.
• Install the proper fuse in the fuse holder in the main
disconnect panel.
$&+*)+&&".%$$*%$)
Be sure the voltage phase and frequency of the input
power is as specified on the rating plate, located on
the rear of the machine.
Supply line entry provision is in the case rear panel.
&%-($&+*%$$*%$
A 10 ft. power cord is provided and wired into the
machine. Follow the power cord connection instruc-
tions. Incorrect connection may result in equipment
damage.
)8=6;4&70B4=?DC Connect green lead to ground
per National Electrical Code. Connect black and white
or brown leads to power. Wrap red lead with tape to
provide 600V insulation.
*7A44&70B4=?DC Connect green lead to ground
per National Electrical Code. Connect black, red and
white or brown leads to power.
)8
-($$
+*%$
+*%$