Filter
Top Products
B-5
OPERATION
B-5
WELDING IN STICK MODE
1. Put the electrode holder and cable quick connect
plug into the proper receptacle for the electrode
polarity desired. Turn clockwise until tight. Connect
the work clamp to the other receptacle and the work
piece.
2. Set the Welding Process Switch to “STICK”.
3. Set the Local/Remote Switch to “Local”.
4. Place the electrode in the electrode holder.
5. Turn the Power Switch to the proper input voltage
setting to turn on the welder.
6. Adjust the Current Control to the desired amps.
7. Strike an arc and weld.
NOTE: When the Welding Process Switch is set to
“STICK” the output is always on when the power
switch is on. A remote control has no effect on the
welding current and the gas flow and high frequency
TIG arc starter are disabled.
INVERTEC V200-T
In Stick Mode the output terminal and
electrode will be electrically hot when-
ever the power switch is turned on.
WARNING
RECOMMENDED ELECTRODE AMPERAGE RANGES - INVERTEC V200-T
The Invertec V200-T is rated from1 - 200 Amps.
SMAW Process
ELECTRODE POLARITY 3/32" 1/8" 5/32"
Fleetweld 180 DC+ 40 - 80 55 - 110 105 - 135
Fleetweld 37 DC+ 70 - 95 100 - 135 145 - Max
Fleetweld 47 DC- 75 - 95 100 - 145 135 - Max
Jet-LH MR DC+ 85 - 110 110 - 160 130 - Max
Blue Max Stainless DC+ 40 - 80 75 - 110 95 - 110
Red Baron Stainless DC+ 40 - 70 60 - 100 90 - 140
Mild steel procedures are based on recommended procedures listed in C2.10 8/94 and the maximum rating of the Invertec V200-T
Jet-LH MR procedures are based on Jet-LH 78 MR
Blue Max procedures are based on C6.1 6/95
Red Baron Procedure are based on ES-503 10/93
GTAW Process
Electrode Polarity DC- Approximate Argon
Electrode Tip Prepration Sharpened Gas Flow Rate
Electrode Type
C.F.H. (l/min.)
EWTh-1, EWCe-2
EWTh-2, EWLa-1 Stainless
Electrode Size (in.) EWG Aluminum Steel
.010 Up to 15 A. 3-8 (2-4) 3-8 (2-4)
.020 Up to 15 A. 5-10 (3-5) 5-10 (3-5)
.040 Up to 80 A. 5-10 (3-5) 5-10 (3-5)
1/16 Up to 150 A. 5-10 (3-5) 9-13 (4-6)
3/32 Up to MAX. A. 13-17 (6-8) 11-15 (5-7)
1/8 X 15-23 (7-11) 11-15 (5-7)
Tungsten electrodes are classified as follows by the American Welding Society (AWS):
Pure..................................EWP........green
+1% Thoria.......................EWTh-1...yellow
+2% Thoria.......................EWTh-2...red
+2% Ceria.........................EWCe-2...orange
+1.5% Lanthana ...............EWLa-1...black
+0.15 to 0.40% Zirconia....EWZr.......brown
Ceriated Tungsten is now widely accepted as a substitute for 2% Thoriated Tungsten in AC and DC applications.
Sept97