Milwaukee 2663-059 Impact Driver User Manual


  Open as PDF
of 16
 
13
OPERATION
WARNINGToreduce therisk ofin-
jury,keephandsawayfromallmovingparts.
Alwayswearsafetygogglesorglasseswith
sideshields.
WARNING Alwaysremove battery
packbeforechangingorremovingaccesso-
ries.Onlyuseaccessoriesspecicallyrecom-
mendedforthistool.Othersmaybehazardous.
UsingControlSwitch
The control switch may be set to three positions: for-
ward, reverse and lock. Due to a lockout mechanism,
the control switch can only be adjusted when the trig-
ger is not pressed. Always allow the motor to come
to a complete stop before using the control switch.
1. For forward(clockwise) rotation, push the con-
trol switch from the right side of the tool. Check
the direction of rotation before use.
2. For reverse (counterclockwise) rotation, push
the control switch from the left side of the tool.
Check the direction of rotation before use.
3. To lock the trigger, push the control switch to the
center position. The trigger will not work when
the control switch is in the locked position.
Always remove the battery pack before perform-
ing maintenance, changing accessories, storing
the tool and any time the tool is not in use.
Starting,StoppingandControllingSpeed
These tools may be operated at any speed from
0 to full speed.
1. To start the tool, pull the trigger.
2. To varythe driving speed, increase or decrease
pressure on the trigger. The further the trigger is
pulled, the greater the speed.
3. To stop the tool, release the trigger.
ImpactingTechniques
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging the
fasteners or workpieces, avoid excessive impact-
ing. Be particularly careful when impacting smaller
fasteners because they require less impacting to
reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasten-
ers are too tight, reduce the impacting time. If they
are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or
under the head of the fastener affects the degree
of tightness.
The torque required to loosen a fastener averages
75% to 80% of the tightening torque, depending on
the condition of the contacting surfaces.
On light gasket jobs, run each fastener down to a
relatively light torque and use a hand torque wrench
for nal tightening.
Inserting/RemovingtheBattery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING Useonlysocketsandother
accessoriesspecicallydesignedforuseon
impactwrenchesanddrivers.Othersockets
andaccessoriesmightshatterorbreakcaus-
inginjury.
ASSEMBLY
WARNING Rechargeonlywiththechar-
gerspeciedforthebattery.Forspeciccharg-
inginstructions,read the operator’smanual
suppliedwithyourchargerandbattery.
WARNING Alwaysremovebattery
packbefore changing or removing acces-
sories.Onlyuse accessories specifically
recommendedfor thistool.Others maybe
hazardous.
AttachingandRemovingAccessories
These tools are intended only for use with acces-
sories designed for impact wrenches and drivers.
Other sockets could shatter or break, causing injury.
1. Use only the appropriate size Square Drive
Sockets.
2. To attach a socket, align the accessory with the
drive shank and push it rmly over the retaining ring.
3. To remove the accessory, pull the accessory off
the drive shank.
 previous next