Filter
Top Products
4
5
SERVICE
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fi re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, fl ush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
• Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
FUNCTIONAL DESCRIPTION
SYMBOLOGY
CE Conformity Mark
WARNING! To reduce the risk of
personal injury, user must read and
understand Operator’s Manual.
1. Handle
2. Band Saw
3. Mounting Vise
4. Chain Hook
5. Swivel Pin
6. Crank Nut
7. Chain
8. Work Surface
9. Mounting Block
Clamp
Mounting Bracket/Block For use with:
28-10-0340/42-28-0220
(Installed)
Most newer-model MILWAUKEE Band Saws, such as:
2729-20 M18™ Fuel™ Band Saw
6232-20 Deep Cut Variable Speed Band Saw
6238-20 Deep Cut Band Saw
28-10-0325/42-28-0250
(Packaged separately in box)
Most older-model MILWAUKEE Band Saws, such as:
0729-20 M28™/ V28™ Deep Cut Band Saw
6223 Deep Cut Band Saw
6225 Deep Cut Band Saw
6230 Deep Cut Band Saw
6232 Band Saw
6232N Deep Cut Band Saw
6236 Deep Cut Band Saw
6236N Deep Cut Band Saw
10. Locking Pin
11. Mounting Block (42-28-0220)
12. Mounting Bracket (28-10-0340)
13. Dampening Screw
14. Front Handle Retaining Screw
1
4
5
6
7
3
2
9
8
10
12
11
14
13
ASSEMBLY
28-10-0340
Mounting Bracket
Mounting on Workbench
The MILWAUKEE Band Saw Table must be
mounted to a wooden or metal workbench with four
bolts. Be sure to choose a location with suffi cient
room on each side to accommodate the cutting of
long stock.
Mounting on Portable Legs
WARNING To reduce the risk of per-
sonal injury caused by tipping, use legs of
equal lengths that will provide a comfortable
working height. Keep table level, place stand
securely on level surface. Support overhang-
ing stock.
The MILWAUKEE Band Saw Table is equipped
with four pipe connectors, located on the under-
side of the table, to accommodate 3/4" threaded
pipe for use as legs. This converts the table
into a stand. The legs are not provided with the
table. The length of the legs should be less than
31" (790 mm).
Installing the Mounting Bracket
WARNING To reduce the risk of injury,
always un plug tool or remove battery pack
before mounting to or removing from table.
Do not transport the saw when attached to
the table.
For use with Band Saws requiring the 28-10-0340
Mounting Bracket and 42-28-0220 Mounting
Block
The MILWAUKEE Band Saw Table is shipped with
the 42-28-0220 Mounting Block installed.
With the table properly mounted on a bench or legs,
place the mounting block in the position shown in
Fig. 1. Line up the holes in the mounting bracket
with the holes in the mounting block, and secure
in place with the washers and socket head screws,
as shown (Fig. 1).
Fig. 1
3/8"
Washer
3/8"-16 x 1"
Socket Head
Screw
42-28-0220
Mounting
Block
Mounting
Block
Clamp
Fig. 2
1/2"-13 x 3-1/2"
Socket Head Cap Screw
Split Ring
42-28-0250
Mounting Block
Locking Pin
Spring
Locking
Pin
Friction
Pad
Mounting
Block Clamp
1/2" Bellville
Washers
1/2"-13
Jam Nuts
1/2" Bellville
Washers
For use with Band Saws requiring the 28-10-0325
Mounting Bracket and 42-28-0250 Mounting
Block
The MILWAUKEE Band Saw Table is shipped
with the 42-28-0220 Mounting Block installed.
To use older MILWAUKEE Band Saws, the
42-28-0220 Mounting Block must be removed, and
the 42-28-0250 Mounting Block must be installed.
With the table properly mounted on a bench or
legs (Fig. 2) :
NOTE: Retain all hardware for mounting the
42-28-0250 mounting block.
Removing the 42-28-0220 Mounting Block
1. Disassemble the locking pin by removing the
split ring from the end of the pin. Pull the pin
and spring out from the other side of the mount-
ing block.
2. Remove the socket head cap screw, washers,
nuts, and friction pad from the mounting block.
Installing the 42-28-0250 Mounting Block
3. Slide the locking pin spring over the locking
pin, and insert into the mounting block from the
mounting block clamp side of the block. Insert
the split ring into the end of the pin.
4. Place the small, offcenter hole of the frinction pad
over the locking pin, line up the center hole with
the large hole in the mounting block.
5. Line up the mounting block with the mount-
ing block clamp, and secure in place with the
socket head cap screw, washers, nuts, as shown.
Counter-torque the 1/2"-13 Jam Nuts together
securely.