Filter
Top Products
14 15
ACCESSORIES
For a complete listing of accessories refer
to your
MILWAUKEE
Electric Tool catalog
or go on-line to www.milwaukeetool.com.
To obtain a catalog, contact your local dis-
tributor or a service center.
FIVE YEAR TOOL
LIMITED WARRANTY
Every
MILWAUKEE
tool is tested before
leaving the factory and is warranted to be
free from defects in material and work-
manship.
MILWAUKEE
will repair or
replace (at
MILWAUKEE
’s discretion),
without charge, any tool (including battery
chargers) which examination proves to be
defective in material or workmanship from
five (5) years after the date of purchase.
Return the tool and a copy of the purchase
receipt or other proof of purchase to a
MILWAUKEE
Factory Service/Sales
Support Branch location or
MILWAUKEE
Authorized Service Station, freight prepaid
and insured. This warranty does not cover
damage from repairs made or attempted
by other than
MILWAUKEE
authorized
personnel, abuse, normal wear and tear,
lack of maintenance, or accidents.
Battery Packs, Flashlights, and Radios are
warranted for one (1) year from the date
of purchase.
THE REPAIR AND REPLACEMENT REMEDIES
DESCRIBED HEREIN ARE EXCLUSIVE. IN NO
EVENT SHALL
MILWAUKEE
BE LIABLE
FOR ANY INCIDENTAL, SPECIAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING
LOSS OF PROFITS.
THIS WARRANTY IS EXCLUSIVE AND IN
LIEU OF ALL OTHER WARRANTIES, OR
CONDITIONS, WRITTEN OR ORAL,
EXPRESSED OR IMPLIED FOR
MERCHANTABLILITY OR FITNESS FOR
PARTICULAR USE OR PURPOSE.
This warranty gives you specific legal
rights. You may also have other rights that
vary from state to state and province to
province. In those states that do not allow
the exclusion of implied warranties or
limitation of incidental or consequential
damages, the above limitations or
exclusions may not apply to you. This
warranty applies to the United States,
Canada, and Mexico only.
WARNING!
To reduce the risk of injury,
always unplug the tool before
attaching or removing
accessories. Use only specifically
recommended accessories.
Others may be hazardous.
Maintaining Tools
Keep your tool in good repair by adopting a
regular maintenance program. Before use,
examine the general condition of your tool.
Inspect guards, switches, tool cord set and
extension cord for damage. Check for
loose screws, misalignment, binding of
moving parts, improper mounting, broken
parts and any other condition that may af-
fect its safe operation. If abnormal noise
or vibration occurs, turn the tool off imme-
diately and have the problem corrected
before further use. Do not use a damaged
tool. Tag damaged tools “DO NOT USE” until
repaired (see “Repairs”).
Under normal conditions, relubrication is
not necessary until the motor brushes
need to be replaced. After six months to
one year, depending on use, return your
tool to the nearest
MILWAUKEE
service
facility for the following:
• Lubrication
• Mechanical inspection and cleaning
(gears, spindles, bearings, housing,
etc.)
• Electrical inspection (switch, cord,
armature, etc.)
• Testing to assure proper mechanical
and electrical operation
WARNING!
To reduce the risk of injury,
always unplug your tool before
performing any maintenance.
Never disassemble the tool or try
to do any rewiring on the tool's
electrical system. Contact a
MILWAUKEE
service facility for
ALL repairs.
WARNING!
To reduce the risk of injury,
electric shock and damage to the
tool, never immerse your tool in
liquid or allow a liquid to flow
inside the tool.
MAINTENANCE
Cleaning
Clean dust and debris from vents. Keep
the tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp
cloth to clean your tool since certain clean-
ing agents and solvents are harmful to plas-
tics and other insulated parts. Some of
these include: gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning
solvents, ammonia and household deter-
gents containing ammonia. Never use flam-
mable or combustible solvents around
tools.
Repairs
If your tool is damaged, return the entire
tool to the nearest service center.
Quik-Lok
®
Cord Sets
10' Quik-Lok
®
Cord Cat. No. 48-76-5010
25' Quik-Lok
®
Cord Cat. No. 48-76-5025
Carrying Case
Cat. No. 48-55-2055
Orbital Pipe Clamp System
Cat. No. 49-22-1016
Keyed Blade Clamp Kit
Cat. No. 49-22-5016
See Pages 46 & 47 for a listing of Super
Sawzall
®
Blades.