Filter
Top Products
8 9
Installing Sausage Type Pack
Always check sausage packs for punc-
tures or damage to the pack before install-
ing. Do not use a damaged or frozen pack.
1. Lock trigger or remove battery pack.
2. Press in and hold rod release trigger.
3. Grasp plunger rod handle and pull
plunger rod back to allow sausage
pack to fit inside barrel tube.
4. Insert pack into barrel tube.
5. Cut off end of sausage pack.
NOTE: Before using a partially filled
pack, remove any hardened material.
1. Lock trigger or remove battery pack.
2. Press in and hold rod release trigger.
3. Grasp plunger rod handle and pull
plunger rod back until the rod tip is just
inside of tool.
4. Release rod release trigger.
5. Position spacer and back cap (fine
threads) onto nose of the tool. The
side of the spacer with the double
collar fits inside the back cap.
6. Place backing washer on top of back
cap and thread barrel nut into nose of
the tool as shown. Tighten securely
using the wrench provided.
7. Press rod release trigger and push
plunger rod forward to access the tip
of the on rod.
8. Thread extenstion, plunger, barrel
plunger and nut onto the plunger rod in
the order shown. Tighten securely.
9. Thread barrel into back cap.
10. To remove barrel tube, reverse procedure.
Installing Caulk or Adhesive Tube
1. Lock trigger or remove battery pack.
2. Cut nozzle of tube at an angle and
size per manufacturer's recommenda-
tion to suit the job. A smaller nozzle
diameter requires more force to push
the caulk and reduces battery life.
3. Break inner seal of tube using a long
nail or piece of wire. If the inner seal
is not broken, the caulk material may
be forced out the rear end of the tube
and damage the tool.
NOTE: Before using a partially filled
tube, remove any hardened material
with a long nail or piece of wire.
4. Press in and hold rod release trigger.
5. Grasp plunger rod handle and pull
plunger rod back to allow the caulk
tube to fit inside carriage frame.
6. Insert caulk tube into carriage frame.
7. Push plunger rod handle forward until
the plunger is against the caulk tube.
8. Release rod release trigger.
OPERATION
6. Insert nozzle supplied with the sau-
sage pack into the nozzle cap (coarse
thread). Thread nozzle cap onto the
front of barrel tube (Fig. 5).
7. Cut nozzle at an angle and size per
manufacturer's recommendation to suit
the job. A smaller nozzle diameter re-
quires more force to push the caulk
and reduces battery life.
8. Press in and hold rod release trigger.
9. Push plunger rod handle forward until
plunger is against sausage pack.
10. Release rod release trigger.
Starting and Stopping and Controlling
Speed
1. Pull trigger to dispense caulk.
2. Increase or decrease pressure on trig-
ger to adjust the speed for proper bead
width and material feed rate. Material
type, temperature and nozzle diameter
will all affect flow rate. When using a
tube or pack with a smaller nozzle di-
ameter use a slower speed or the
material may be forced around the rear
tube seat.
3. Release trigger to stop dispensing
caulk.
Locking the Trigger (Fig. 6)
Always lock trigger or remove battery pack
before changing accessories or perform-
ing maintenance. Lock trigger when the
tool is not in use and when storing the tool.
1. To lock the trigger, push trigger lock
in the direction shown. The trigger will
not work when the trigger lock in the
locked position.
2. To unlock the trigger, push the trigger
lock in the direction shown.
WARNING!
When tool is not in use, lock trig-
ger to prevent the tool from be-
ing accidentally turned on.
Fig. 6
Locked
Unlocked
Adjusting Plunger Rod
1. To manually adjust plunger rod, press
in and hold rod release trigger.
2. Grasp plunger rod handle and either
push or pull rod in or out.
3. Release rod release trigger.
NOTE: Keep plunger rod clean of material.
Retracting a plunger that is covered with
material may damage the internal parts of
the tool.
Installing Barrel Assembly (Cat. No. 6560-24) (Fig.5)
6560-24
Fig. 5
Barrel
Plunger rod
Plunger
Backing washer
Back cap
Spacer
Barrel plunger
Barrel nut
Nut
Nozzle cap
Nozzle
Double collar
Extension