Filter
Top Products
2
SAFETY RULES
1. Know your machine. Read this manual carefully.
Learn the machine’s applications and limitations,
as well as specific potential hazards peculiar to it.
2. Ground all machines. If the machine is equipped
with three-pin plug, it should be plugged into a
three-pin electrical socket. Never remove the
ground pin.
3. Avoid body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your
body is grounded.
4. Do not expose tool to moisture. Don’t use this
machinery in damp or wet locations. Keep out of
rain.
5. Do not abuse cord. Never use the cord to carry
tools or pull the plug from an outlet. Keep cord
away from heat, sharp edges or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electric shock.
6. Remove adjusting keys or wrenches before
turning the tool on. A wrench or key that is left
attached to a moving part of the tool may result in
personal injury.
7. Keep work area clean and well lit. Cluttered or
dark work areas invite accidents.
8. Keep children away. All children should be kept
away from the work area. Never let a child handle
a tool without strict adult supervision.
9. Do not operate this tool if under the influence of
alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there
is any doubt, do not attempt to operate.
10. Use safety equipment. Eye protection should be
worn at all times when operating this machine.
Use ANSI approved safety glasses. Everyday
eyeglasses only have impact resistant lenses.
They are NOT safety glasses. Dust mask, non-
skid safety shoes, hard hat, or hearing protection
should be used in appropriate conditions.
11. Wear proper apparel. Loose clothing, gloves,
neckties, rings, bracelets, or other jewelry may
present a potential hazard when operating this
machine. Please keep all apparel clear of the
machine.
12. Don’t overreach. Keep proper footing and balance
at all times when operating this product.
13. Always disconnect the machine from power
source before making any adjustments, storing,
servicing, or changing accessories. Such
preventative safety measures reduce the risk of
starting the tool accidentally.
14.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it was designed.
15.
Do not use the tool if the switch does not turn it
on and off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
16. Check for damage. Check your tool regularly. If
part of the tool is damaged it should be carefully
inspected to make sure that it can perform its
intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a qualified
technician. Consult your dealer for advice.
17. Keep away from flammables. Do not attempt to
operate this tool near flammable materials or
combustibles. Failure to comply may cause
serious injury or death.
18. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in the
hands of untrained users.
19. Maintain tools with care. Keep tools sharp and
clean. Properly maintained tools, with sharp
cutting edges, are less likely to bind and are
easier to control.
20. Never exceed the pressure rating of any
component in system.
21. Protect material and air lines from damage or
puncture. Keep hose and power cable away from
sharp objects, moisture, chemicals, oil, etc.
22. Check condition of hoses before each use. Do not
use a damaged hose. If hose is damaged,
replace immediately.
23. Read, understand and comply with all warning
labels on unit.
24. Drain tank of moisture after each use. If
Compressor is not to be used for extended
periods of time, leave tank drain valve open to
allow moisture to completely drain from tank.
25. Do not tamper with Safety Valve. The Safety
Valve is factory set for your model air compressor.
Any user adjustments to Safety Valve will
automatically void warranty.
26. Air compressors get hot while in operation.
NEVER touch the motor, discharge tubing or
compressor pump while in operation.
27.
The Compressor operates automatically while the
motor is turned on.
28. Compressed air from the unit may contain carbon
monoxide.
Air produced is not suitable for
breathing purposes.
29.
Always use a respirator when spraying paint or
chemicals.
30. The air pressure switch is set at the factory for
optimum performance of your equipment. Never
attempt to bypass or remove this switch as
serious damage to equipment or personal injury
could result from excessive air pressure.