Filter
Top Products
3
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
n Keep your work area clean and well lit. Cluttered benches
and dark areas invite accidents.
n Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or
dust. Power tools create sparks which may ignite the dust
or fumes.
n Keep bystanders, children, and visitors away while op-
erating a power tool. Distractions can cause you to lose
control.
Electrical Safety
n Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double insulation
eliminates the need for the three-wire grounded power
cord and grounded power supply system.
n Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an in-
creased risk of electric shock if your body is grounded.
n Don't expose power tools to rain or wet conditions. Wa-
ter entering a power tool will increase the risk of electric
shock.
n Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away from
heat, oil, sharp edges, or moving parts. Replace damaged
cords immediately. Damaged cords increase the risk of
electric shock.
n When operating a power tool outside, use an outdoor ex-
tension cord marked "W-A" or "W". These cords are rated
for outdoor use and reduce the risk of electric shock.
Personal Safety
n Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool while
tired or under the influence of drugs, alcohol, or medica-
tion. A moment of inattention while operating power tools
may result in serious personal injury.
n Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
n Avoid accidental starting. Be sure switch is off before
plugging in. Carrying tools with your finger on the switch
or plugging in tools that have the switch on invites ac-
cidents.
n Remove adjusting keys or wrenches before turning the
tool on. A wrench or a key that is left attached to a rotat-
ing part of the tool may result in personal injury.
n Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enables better control
of the tool in unexpected situations.
n Use safety equipment. Always wear eye protection. Dust
mask, nonskid safety shoes, hard hat, or hearing protec-
tion must be used for appropriate conditions.
n Do not wear loose clothing or jewelry. Contain long hair.
Loose clothes, jewelry, or long hair can be drawn into air
vents.
n Do not use on a ladder or unstable support. Stable foot-
ing on a solid surface enables better control of the tool
in unexpected situations.
Tool Use and Care
n Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by
hand or against your body is unstable and may lead to
loss of control.
n Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate
for which it is designed.
n Do not use tool if switch does not turn it on or off. Any tool
that cannot be controlled with the switch is dangerous
and must be repaired.
n Disconnect the plug from power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
n Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
n Maintain tools with care. Keep cutting tools sharp and
clean. Properly maintained tools with sharp cutting edges
are less likely to bind and are easier to control.
n Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
n Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
n Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool. Fol-
lowing this rule will reduce the risk of loss of control and
deterioration of the enclosure plastic.
GENERAL SAFETY RULES