Ryobi RJ150V Cordless Saw User Manual


 
Page 3
READ ALL INSTRUCTIONS
1. KNOW YOUR POWER TOOL - Read owner's
manual carefully. Learn its applications and limita-
tions as well as the specific potential hazards
related to this tool.
2. GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH
GROUNDED SURFACES. For example: Pipes,
radiators, ranges, refrigerator enclosures.
3. KEEP GUARDS IN PLACE and in working order.
4. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
5. AVOID DANGEROUS ENVIRONMENT. Don't use
power tool in damp or wet locations or expose to
rain. Keep work area well lit.
6. KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
7. STORE IDLE TOOLS. When not in use, tools
should be stored in a dry, high or locked-up place
- out of the reach of children.
8. DON'T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or at-
tachment to do the job of a heavy duty tool. Don't
use tool for purpose not intended - for example -
Don't use a circular saw for cutting tree limbs or
logs.
10. WEAR PROPER APPAREL. No loose clothing or
jewelry to get caught in moving parts. Rubber
gloves and non-skid footwear are recommended
when working outdoors. Also, wear protective hair
covering to contain long hair and keep it from being
drawn into air vents.
11. ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
12. PROTECT YOUR LUNGS. Wear a face or dust
mask if operation is dusty.
13. PROTECT YOUR HEARING. Wear hearing pro-
tection during extended periods of operation.
14. DON'T ABUSE CORD. Never carry tool by cord or
yank it to disconnect from receptacle. Keep cord
away from heat, oil and sharp edges.
15. SECURE WORK. Use clamps or a vise to hold
work. Both hands are needed to operate the tool.
16. DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
17. MAINTAIN TOOLS WITH CARE. Keep tools sharp
at all times, and clean for best and safest perfor-
mance. Follow instructions for lubricating and
changing accessories.
18. DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades,
bits, cutters, etc., all tools should be disconnected
from power supply.
19. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
20. AVOID ACCIDENTAL STARTING. Don't carry
plugged-in tools with finger on switch. Be sure
switch is off when plugging in.
21. MAKE SURE YOUR EXTENSION CORD IS IN
GOOD CONDITION. When using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of
power and overheating. A wire gage size (A.W.G.)
of at least 12 is recommended for an extension
cord 100 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use the
next heavier gage. The smaller the gage number,
the heavier the cord.
22. OUTDOOR USE EXTENSION CORDS. When
tool is used outdoors, use only extension cords
intended for use outdoors and so marked.
23. KEEP BLADES CLEAN AND SHARP. Sharp
blades minimize stalling and kickback. Also, keep
blades properly tightened at all times.
24. KEEP HANDS AWAY FROM CUTTING AREA.
Keep hands away from blades. Do not reach
underneath work while blade is cutting. Do not
attempt to remove material while blade is cutting.
25. NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
26. INSPECT TOOL CORDS PERIODICALLY and if
damaged, have repaired by an authorized service
center. Stay constantly aware of cord location.
27. INSPECT EXTENSION CORDS PERIODICALLY
and replace if damaged.
28. KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids, gaso-
line, petroleum-based products or any strong sol-
vents to clean your tool.