Filter
Top Products
With a wide bladed screwdriver, unscrew valve plug
(1
1).
Take out air regulator(8) with O-rings
(9)
and
(1
0);
spring
(7)
and pin throttle
(6)
with O-rings (4) and
(5).
Remove O-rings (4) and
(5)
from pin throttle
(6).
If
a
replacement is required, push out throttle bushing
(2)
complete
with
O-rings
(3)
and remove
2
O-rings
(3)
from throttle bushing (2).
Reassembly
Clean all parts and examine for wear and replace any
parts
only with parts obtained from the manufacturer or
an
approved distributor.
Ensure that the faces of end plates (17) and
(22)
that abut cylinder (21) are flat and free from burrs and surface defects. If necessary, lap
on
a
flat very fine grade of abrasive paper.
Lightly coat all parts In a suitable pneumatic tool lubricating oil and pack bearings with
a
lithium or molfldenum based general purpose
grease and reassemble in the reverse order.With the lever (12) depressed pour into hose adaptor (14)
5ml
of a suitable pneumatic tool
lubricating oil and release lever and connect to a suitable air supply and operate tool slowly for a few seconds to allow the oil to circulate.
Check the function of the collet, safety lever and air regulator before returning to service. Before fitting mounted point grinding wheel,
check tool, the speed of the tool and the point
-
refer to section "Operating".
1
Ooeration
Soecification
1
Average Air Consumption
1
4.0
cfrn
(28scfm)
Air Inlel Thread
1
114-18NPT
Overall Length
1
6.1"
(155mm)
at
90
PSIGt6.2 bar
SiouxTools
Inc.
2901
Floyd Boulevard
P.O.
Box
507
Sioux
City,
IA
51 102
U.S.A.
Tel No. 712-252-0525 Fax
No.
71
2-252-4267
Product Net Weight Recommended
Use
Of
0.83
Ibs
1
Balancer Or Support
Air Pressure
Recommended Working
6.2
bar
90
PSI
Maximum
6.2
bar
90
PSI
SAFETY MESSAGES
1
A
WARNING
Personal
Safety
Equipment
Always Read Inslructfons
Use
-
Safety Glasses
VES
1
Before Using PowerTools
Always Wear Safety
Use
-
Safety Gloves
YES
@
Goggles
Use
-
Safety
Boots
1
ffi
WW~ Hearing Protac!ion
Use
-
Breathing Masks
YES
Use
-
Ear Protectors
ATOM Prolonged Exposure
I
ÇVlbrat
NOTES
Product Type
RPM
114"
Heavy
Duty
Cycles Per Min.
Die Grinder
27000
ce
Model No/Nos
I
Serial
No.
Size
-
Minimum Hose Length
Noise
Level:
Sound Pressure
Level
82.9
dB(A)
Test Method:
Tested in accordance
with
Pneurop
test
code
PN8NTC1
and IS0 Standard
3744
Vibration
Level
Less
than
2.0
Meters
1
Sec2
Test Method:
Tested in accordance
with
IS0
standards
8662
Parts
1
&
13
Declaration
of
Conformity
Sioux
Tools
Inc.
2901 Floyd Boulevard.
P.O.
Box
507,
Sioux
City. Iowa
51 102
declare under our sole responsibility lhat the product
Model
5062
114"
Heavy
Duty
Die
Grinder,
Serial
Number
to which this declaration relates Is in conformity with the following standard(s) or other normative document(s)
EN792
(Draft),
EN292 Parts
1
&
2,
IS0
8662
Parts
1
&
13,
Pneurop PN8NTC
1
following
~~O~~OVIS~OIIS
of
&
931441~~~
Directives
(V.PJGeneral
Manager)
---------------
---------------
---------------
<
Name and signature or aquhffllent marking
of
authorlied person
Â¥Ã
Page
No
4
Printed
in
Taiwan