Skil 4570 Cordless Saw User Manual


 
//1??;>51?
2 -: 1D@1:?5;: /;>0 5?
:1/1??->E -/;>0 C5@4
-01=A-@1?5F1/;:0A/@;>?@4-@5?/-<-.81
;2/->>E5:3@41/A>>1:@:1/1??->E2;>E;A>
@;;8 9A?@ .1 A?10 This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
!"&The smaller the gauge number, the
heav i er the cord.
$" !%,%"*&!%"!"$%
("&&$!&!'$$!&&""%
!
WARNING
&;;8H?
9<1>1
$-@5:3
;>0%5F15:)
)5>1%5F1?5:99
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0
14 12 —— ————
25 50 100 150 15 30 60 120
;>01:3@45:11@
;>01:3@45: 1@1>?
-18-
%1>B5/1
!"'%$%$(
#$&%!%#>1B1:@5B1
9-5:@1:-:/1<1>2;>910.EA:-A@4;>5F10
<1>?;::189-E>1?A8@5:95?<8-/5:3;2
5:@1>:-8C5>1?-:0/;9<;:1:@?C45/4
/;A80/-A?1?1>5;A?4-F->0 We recom -
mend that all tool service be performed by a
Skil Factory Service Center or Authorized Skil
Service Station. SERVICE MEN: Disconnect
tool and/or charger from power source before
servicing.
&&$%
1-81>@2;>.-@@1>E<-/7?@4-@->1:1->5:3
@415>1:0;28521 If you notice decreased
tool performance or significantly shorter
running time between charges then it is time
to replace the battery pack. Failure to do so
can cause the tool to operate improperly or
damage the charger.
! ' &&$% "!+
;:3@1>9.-@@1>E?@;>-31?4;A80.15:
@4105?/4->310?@-@1 Battery packs last
longer and re-charge better when they are
stored discharged. Remember to fully re-
charge battery packs before using after
prolonged storage.
&""'$&"!
Your Skil tool has been properly lubricated
and is ready for use.
 "&"$%
The motor in your tool has been engineered
for many hours of dependable service. To
maintain peak efficiency of the motor, we
recommend it be examined every six months.
Only a genuine Skil replacement motor
specially designed for your tool should be
used.
81-:5:3
&;-B;50-//501:@?-8C-E?
05?/;::1/@@41@;;8-:0;>
/4->31>2>;9@41<;C1>?A<<8E.12;>1
/81-:5:3 The tool may be cleaned most
effectively with com pressed dry air. 8C-E?
C1->?-21@E3;3381?C41:/81-:5:3@;;8?
C5@4/;9<>1??10-5>
Ventilation openings and switch levers must
be kept clean and free of foreign matter. Do
not attempt to clean by inserting pointed
objects through opening.
1>@-5:/81-:5:3-31:@?
-:0 ?;8B1:@? 0-9-31
<8-?@5/<->@?Some of these are: gasoline,
car bon tetrachloride, chlorinated cleaning
solvents, ammonia and household detergents
that contain ammonia.
!
WARNING
-5:@1:-:/1
!
WARNING
!
CAUTION
SM 1619X04463 05-09:SM 1619X04463 05-09 5/29/09 3:22 PM Page 18