Filter
Top Products
6 ► IW12 User Manual
The safety tag (P/N 15875) at right is
attached to the tool when shipped from the
factory. Read and understand the safety
instructions listed on this tag before removal.
We suggest you retain this tag and attach it
to the tool when not in use.
NOTE:
THE INFORMATION LISTED ON
THE STICKERS SHOWN, MUST
BE LEGIBLE AT ALL TIMES.
REPLACE DECALS IF
THEY BECOME WORN OR
DAMAGED. REPLACEMENTS
ARE AVAILABLE FROM
YOUR LOCAL STANLEY
DISTRIBUTOR.
28322
CE DECAL (CE)
11207
CIRCUIT TYPE D
DECAL (CE)
D
30LPM@138BAR
EHTMACATEGORY
73683
IW12 NAME TAG (US & CE)
Failuretousehydraulichoselabeledandcertified
asnon-conductivewhenusinghydraulictoolson
ornearelectriclinesmayresultindeathor
Forproperandsafeoperationreadownersmanual
andmwkesurethatyouhavebeenproperly
trainedincorrectproceduresrequiredforwork
seriousinjury.
onoraroundelectriclines.
ELECTROCUTION
HAZARD
DANGER
12412
DANGER DECAL
29083
ROTATION DIRECTION
DECAL
29530
SOUND POWER
LEVEL DECAL (CE)
Lw a
03788
GPM DECAL
4-12 GPM / 15-45 LPM
DO NOT EXCEED 2000 PSI / 140 BAR
DO NOT EXCEED SPECIFIED FLOW OR PRESSURE USE
CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM.
USE OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM.
CORRECTLY CONNECT HOSES TO TOOL ‘IN’ AND ‘OUT’
PORTS. IMPROPER HANDLING,USE OR OTHER MAINTE-
NANCE OF TOOL COULD RESULT IN A LEAK OR BURST OR
OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST
CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY.
17275
GPM/PRESSURE DANGER DECAL
DANGER
ELECTROCUTION
HAZARD
Failure to use hydraulic hose labeled and certi ed as
non-conductive when using hydraulic tools on or near
electric lines may result in death or serious injury.
For proper and safe operation read owners manual
and make sure that you have been properly trained
in correct procedures required for work on or around
electric lines.
4-12 GPM / 15-45 LPM
DO NOT EXCEED 2000 PSI / 149 BAR
◘ DO NOT EXCEED SPECIFIED FLOW OR PRESSURE ◘ USE
CLOSED-CENTER TOOL ON CLOSED-CENTER SYSTEM. ◘ USE
OPEN-CENTER TOOL ON OPEN-CENTER SYSTEM. ◘ CORRECTLY
CONNECT HOSE TO TOOL “IN” AND “OUT” PORTS. IMPROPER
HANDLING, USE OR MAINTENANCE OF TOOL COULD RESULT
IN A LEAK, BURST OR OTHER TOOL FAILURE. ◘ CONTACT AT A
LEAK OR BURST CAN CAUSE OIL INJECTIONS INTO THE BODY.
◘ FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN
SERIOUS PERSONAL INJURY.
SAFETY TAG P/N 15875 (Shown smaller then actual size)
DANGERDANGER
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CER-
TIFIED AS NON-CONDUCTIVE WHEN USING HYDRAULIC
TOOLS ON OR NEAR ELECTRICAL LINES MAY RESULT IN
DEATH OR SERIOUS INJURY.
BEFORE USING HOSE LABELED AND CERTIFIED AS NON-
CONDUCTIVE ON OR NEAR ELECTRIC LINES BE SURE THE
HOSE IS MAINTAINED AS NON-CONDUCTIVE. THE HOSE
SHOULD BE REGULARLY TESTED FOR ELECTRIC CUR-
RENT LEAKAGE IN ACCORDANCE WITH YOUR SAFETY
DEPARTMENT INSTRUCTIONS.
2. A HYDRAULIC LEAK OR BURST MAY CAUSE OIL INJEC-
TION INTO THE BODY OR CAUSE OTHER SEVERE
PERSONAL INJURY.
A. DO NOT EXCEED SPECIFIED FLOW AND PRESSURE
FOR THIS TOOL. EXCESS FLOW OR PRESSURE MAY
CAUSE A LEAK OR BURST.
B. DO NOT EXCEED RATED WORKING PRESSURE OF
HYDRAULIC HOSE USED WITH THIS TOOL. EXCESS
PRESSURE MAY CAUSE A LEAK OR BURST.
C. CHECK TOOL HOSE COUPLERS AND CONNECTORS
DAILY FOR LEAKS. DO NOT FEEL FOR LEAKS WITH
YOUR HANDS. CONTACT WITH A LEAK MAY RESULT
IN SEVERE PERSONAL INJURY.
IMPORTANT
D. DO NOT LIFT OR CARRY TOOL BY THE HOSES. DO
NOT ABUSE HOSE. DO NOT USE KINKED, TORN OR
DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROPERLY CON-
NECTED TO THE TOOL BEFORE PRESSURING SYSTEM.
SYSTEM PRESSURE HOSE MUST ALWAYS BE CON-
NECTED TO TOOL “IN” PORT. SYSTEM RETURN HOSE
MUST ALWAYS BE CONNECTED TO TOOL “OUT” PORT.
REVERSING CONNECTIONS MAY CAUSE REVERSE
TOOL OPERATION WHICH CAN RESULT IN SEVERE
PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO CLOSED-
CENTER HYDRAULIC SYSTEMS. THIS MAY RESULT IN
LOSS OF OTHER HYDRAULIC FUNCTIONS POWERED BY
THE SAME SYSTEM AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK AREA.
KEEP BYSTANDERS CLEAR OF YOUR WORK AREA.
6. WEAR HEARING, EYE, FOOT, HAND AND HEAD PRO-
TECTION.
7. TO AVOID PERSONAL INJURY OR EQUIPMENT DAMAGE,
ALL TOOL REPAIR MAINTENANCE AND SERVICE MUST
ONLY BE PERFORMED BY AUTHORIZED AND PROPERLY
TRAINED PERSONNEL.
IMPORTANT
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SEE OTHER SIDE
28788
Manual
Sticker
TOOL STICKERS & TAGS
73680 RAILROAD HELP
DESK DECAL