Filter
Top Products
-6-
Place the nose of the tool against a work piece for all of the following operation checks.
A. With hand on rear end of the handle, further back away from the secondary trigger, and not squeezing the secondary trigger, use finger to pull
the primary trigger.
THE TOOL MUST NOT CYCLE.
B. With hand on handle, and squeezing the secondary trigger, use finger to pull the primary trigger.
THE TOOL MUST CYCLE.
WHILE THE SECONDARY TRIGGER REMAINS SQUEEZED, THE TOOL WILL CYCLE EACH TIME THE PRIMARY TRIGGER IS PULLED!
IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL
OBSERVE THE FOLLOWING FOR SAFE OPERATION
• Use the BOSTITCH pneumatic tool only for the purpose for which it was designed.
• Never use this tool in a manner that could cause a fastener to be directed toward the user
or others in the work area.
• Do not use the tool as a hammer.
• Always carry the tool by the handle with hand off both triggers. Never carry the tool by the air hose.
• Do not alter or modify this tool from the original design or function without approval from BOSTITCH
• Always be aware that misuse and improper handling of this tool can cause injury to
yourself and others.
• Never clamp or tape the trigger or secondary trigger in an actuated position.
• Never leave a tool unattended with the air hose attached.
• Do not operate this tool if it does not contain a legible WARNING LABEL.
• Do not continue to use a tool that leaks air or does not function properly. Notify your
nearest BOSTITCH representative if your tool continues to experience functional problems.
MAINTAINING THE PNEUMATIC TOOL
When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.
REPLACEMENT PARTS:
Use only BOSTITCH replacement. Do not use modified parts or parts which will not give equivalent performance to the original equipment.
AIR SUPPLY-PRESSURE AND VOLUME:
Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the
effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure
reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air
supply from the tool to the supply source for restrictive connectors, swivel fittings, low points containing water and anything else that would prevent full
volume flow of air to the tool.
TROUBLE SHOOTING
PROBLEM CAUSE CORRECTION
Trigger valve stem leaks air O-ring cut or cracked . . . . . . . . . . . . . . . . . . . . . . . . .Replace trigger valve assembly
Failure to cycle Air supply restriction . . . . . . . . . . . . . . . . . . . . . . . . .Check air supply equipment
Air pressure too low . . . . . . . . . . . . . . . . . . . . . . . . . .Check air supply equipment
Lack of power; slow to cycle O-rings/seals cut or cracked . . . . . . . . . . . . . . . . . . .Replace O-rings/seals
Trigger assembly worn/leaks . . . . . . . . . . . . . . . . . . .Replace trigger assembly
Dirt/tar build up on driver . . . . . . . . . . . . . . . . . . . . . .Disassemble nose/driver to clean
Skipping fasteners;
-intermittent feed Air restriction/inadequate air flow through
quick disconnect socket and plug . . . . . . . . . . . . . . .Replace quick disconnect fittings
Worn piston O-ring . . . . . . . . . . . . . . . . . . . . . . . . . .Replace O-ring, check driver
Damaged pusher spring . . . . . . . . . . . . . . . . . . . . . .Replace spring
Low air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . .Check air supply system to tool
Wrong size fasteners . . . . . . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners
Broken/chipped driver . . . . . . . . . . . . . . . . . . . . . . . .Replace driver (check piston O-ring)
Dry/dirty magazine . . . . . . . . . . . . . . . . . . . . . . . . . .Clean
Worn magazine liner . . . . . . . . . . . . . . . . . . . . . . . . .Replace magazine liner
Fasteners jam in tool Wrong size fasteners . . . . . . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners
Bent fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Discontinue using these fasteners
Broken/chipped driver . . . . . . . . . . . . . . . . . . . . . . . .Replace driver