Filter
Top Products
Models/Modelos
CM9130
Owner’s Manual
Manuel de Usuario
• Use only the battery charger that is supplied with this tool. Using another
charger may cause damage to the battery.
• Always remove the battery from the charging base after 3-5 hours.
Do not leave battery in charging base for extended periods of time.
WARNING: Never charge a battery pack again immediately after it has been
fully charged. This can give rise to the battery pack being overcharged and a
reduced battery life. Length of service of your battery will depend on the type
of work you are doing. The batteries in this tool have been designed to provide
maximum, trouble-free life. However, like all batteries, it will eventually wear
out. Do not disassemble battery pack and attempt to replace the batteries.
To make your batteries last as long as possible, we suggest the following:
1. Store and charge your batteries in a cool area. Temperatures above or below
normal room temperatures will shorten battery life.
2. Never store batteries in a discharged condition. Recharge them immediately
after they are discharged.
3. All batteries gradually lose their charge. The higher the temperature the
quicker they lose their charge. If you store your tool for long periods of time
without using it, recharge the batteries every month or two. Getting into this
habit will prolong battery life.
Using The Drill
CAUTION: Always make sure that the tool is switched
OFF and the battery pack is removed from the drill
before changing any bits.
Loosen the keyless chuck by holding the ring and
turning the sleeve counter clockwise. Select the drill bit
or screwdriver you want to use and place it in the
keyless chuck. Twist the sleeve of the keyless chuck
clockwise to tighten it, making sure the drill bit remains
in the center of the keyless chuck’s teeth.
Twist the 24 setting torque control ring to the desired
setting. Lower settings are better for light work such as
driving screws into soft materials. Higher settings are
recommended for drilling into harder surfaces.
When properly adjusted, the clutch will slip at
its present torque setting to prevent driving the
screw too deep or to prevent damage to the tool.
To operate the drill in forward setting,
simply keep the Forward/Lock/Reverse switch flat
against the side of the drill as shown. To change
OPERATION
INSTRUCTIONS FOR USE:
Charging The Battery
THE BATTERY(IES) MAY NOT BE FULLY CHARGED FROM THE FACTORY.
READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO FIRST USE.
Using the Battery Charger
NOTE: Before inserting or removing the battery from the charging base, always
ensure that the base is not plugged into a 120V power source.
1. To begin charging, remove the battery pack from the tool by pressing on the
battery release buttons on either side of the battery pack and pulling down.
2. Plug the battery pack into the battery charger making sure the positive (+) and
negative (-) poles of the battery match the positive (+) and negative (-) poles of
the battery charger.
NOTE: The battery will only fit into the battery charger and the tool one way.
3. Plug one end of the 120 Volt AC Adaptor into the battery charger and the other
end into any standard 120 Volt wall outlet. The RED LED indicator on the battery
charger will illuminate to indicate that the battery is charging.
4. Full charging will take between 3 to 5 hours.
NOTE: While the battery is placed in the charger, the RED LED indicator light
will remain on. If charging more than one battery, wait at least 15 minutes
between each charge. Use only the battery charger that is supplied with this
tool. Using another charger may cause damage to the battery. To increase the
life of your battery, do not leave the battery charging for more than 8 hours.
Battery Warnings
• Your Drill comes complete with a rechargeable battery, we recommend that
you fully charge before the first use.
• Your Drill battery must be charged prior to first use.
• Your battery should be recharged when the drill does not operate up to its
normal performance level. Do not continue to operate the drill in this depleted
capacity. Recharge the battery immediately.
• Over time, if the drill is not used, the battery will lose capacity. For maximum
performance, recharge the battery after prolonged storage or non-use periods.
• If charging more than one battery, wait at least 15 minutes between each
charge.
7
8