S
O
L
I
D
E
D
G
E
MANUFACTURING TOLERANCE PER E2056
UNLESS OTHERWISE SPECIFIED TOLERANCE
SCALE:
DO NOT SCALE THIS DRAWING
ON 3 PLACE DECIMALS IS ± .002
THIS SHEET CONTAINS PROPRIETARY INFORMATION OWNED BY THE LINCOLN ELECTRIC COMPANY AND IS NOT TO BE REPRODUCED, DISCLOSED OR USED WITHOUT THE EXPRESS WRITTEN PERMISSION OF THE LINCOLN ELECTRIC COMPANY, CLEVELAND, OHIO U.S.A.
DESIGN INFORMATION
t
DRAWN BY:
WITH PUBLISHED STANDARDS.
DATE:
ON 2 PLACE DECIMALS IS ± .02
MATERIAL TOLERANCE (" ") TO AGREE
ON ALL ANGLES IS± .5 OF A DEGREE
SUBJECT:
ENGINEER:
EQUIPMENT TYPE:
DRAWING No.:
JB/
MISCELLANEOUS
SPI DISPLAY P.C. BOARD ASSEMBLY
L
FULL
5-11-2000
REFERENCE:
SUPERSEDING:
L11130-2
APPROVED:
11130-3
Chg. Sheet No."X" INFO.
XM5626
XA
6-2-2000A
8-4-2000C
UNLESS OTHERWISE SPECIFIED:
CAPACITORS = MFD/VOLTS
INDUCTANCE = HENRIES
RESISTANCE = OHMS
BUY AS:
IDENTIFICATION CODE
PART NO.
BUY PER E3867
TEST PER E3856-D
54
3
2
1
SPI DISPLAY
L11130-3
R29
X2
X3
X4
X7
X5
X6
LED1 LED2
LED3
LED4
X1 R28
R27
R26
R25
R24
R23
R22
R21
R20
R16
R14
R13
R12
R11
R10
R9
R6
LED7
LED6
LED5
C20
C19
C12
C11
C5
C4
C3
C2
C1
J37
DISP8 DISP7 DISP6 DISP5 DISP4 DISP3 DISP2 DISP1
2
1
GROUND SIDE
V
ENCAPSULATE WITH HUMISEAL 1A27LU PER
E1844 OR WITH EQUIVALENT AS APPROVED
BY LINCOLN ELECTRIC COMPANY. (2 COATS)
NOTES:
N.A. DO NOT COAT WITH ENCAPSULATION MATERIAL.
N.B.
CAUTION: THIS DEVICE IS SUBJECT TO DAMAGE BY STATIC
ELECTRICITY. SEE
E2454 BEFORE HANDLING.
N.C. USE
ITEM 3 TO STAND LED1, LED2,LED3 AND LED4 FROM THE P.C. BOARD. THERE
MUST NOT BE MORE THAN .020 GAP BETWEEN SPACER AND P.C. BOARD OR
BETWEEN SPACER AND LED. ENCAPSULATE P.C.BOARD, SPACER AND LOWER HALF
OF LED.
N.D.
DISP 1 THRU DISP 8 MUST ALWAYS BE MATCHED BY VENDOR NAME.
DO NOT MIX DIFFERENT VENDORS ON THE SAME BOARD ASSEMBLY.
N.E. CONNECTOR MUST BE GREASED WITH
ITEM 4PRIOR TO ENCAPSULATION.
3
N.A.
N.A.
N.A.
0
.50
1.45
1.60
1.75
0
2.95
5.65
5.75
5.90
N.A.,N.E.
LED
N.C.
ITEM REQ'D PART NO. DESCRIPTION
11L11130-D DISPLAY P.C. BOARD BLANK (REF ONLY)
21L11166-1 FLEX CIRCUIT
34T15176-2 LED, SPACER, 0,140 HIGH
4.01 OZ.E3539 ELECTRICAL INSULATING COMPOUND
C1 1 S25024-7SMT CAPACITOR, SMD, TANTALUM, 47ME, 20V, 10%, S7343
C2, C3, C4, C5, C11, C12, C19, 8 S25020-3SMT CAPACITOR, SMD, CERAMIC, 0.1ME, 50V, 10%, X7R, S0805
C20
N.A.,N.D. DISP1, DISP2, DISP3, DISP4 8 S17395-6 LED, DISPLAY, 7-SEGMENT, CC, BRIGHT
DISP5, DISP6, DISP7, DISP8
J37 1 S18248-10 CONNECTOR, MOLEX, MINI, PCB, 10-PIN
N.A. LED1, LED2, LED3, LED4 4 T13657-6 LED, T-1, RED, HLMP-K101
N.A. LED 5, LED6, LED7 3 T13657-12 LED, T-1, 3/4, YELLOW, HIGH-INTENSITY
R6, R16 2 S25000-1501SMT RESISTOR, SMD, METAL FILM, 1/10W, 1.50K, 1%, S0805
R9, R10, R11, R12, R13, R14 6 S25000-1212SMT RESISTOR, SMD, METAL FILM, 1/10W, 12.1K, 1%, S0805
R20 1 S25000-2670SMT RESISTOR, SMD, METAL FILM, 1/10W, 267OHMS, 1%, S0805
R21, R25, R26, R28, R29 5 S25000-1001SMT RESISTOR, SMD, METAL FILM, 1/10W, 1.00K, 1%, S0805
R22, R23 2 S25000-10R0SMT RESISTOR, SMD, METAL FILM, 1/10W, 10.0OHMS, 1%, S0805
R24 1 S25000-4751SMT RESISTOR, SMD, METAL FILM, 1/10W, 4.75K, 1%, S0805
R27 1 S25000-4752SMT RESISTOR, SMD, METAL FILM, 1/10W, 47.5K, 1%, S0805
N.B. X1 1 S17900-8SMT IC, SMD, CMOS, INVERTER, SCHMITT, HEX, HC14A (SS)
N.B. X2 1 S17900-26SMT IC, CMOS, SMD, MUX, DAT, 8-INPUT, HC151 (SS)
N.B. X3 1 S17900-28SMT IC, SMD, CMOS, INVERTING BUFFER, 3-ST (SS)
N.B. X4 1 S17900-10SMT IC, SMD, CMOS, REGISTER, SHFT, S-PI/SO, 8-BIT (SS)
X5, X6, X7 3 S20496-1SMT IC, SMD, CMOS, DRIVER, DISPLAY, LED, CC, MCU
SPECIFICATIONS
FOR ITEMS BELOW REFER TO ELECTRONIC COMPONENTS DATABASE FOR COMPONENT
